Catálogos >
LITOKOL >
Ottoseal S70

Ottoseal S70
1 / 4Páginas

Excertos do catálogo

Ottoseal S70 SINGLE-COMPONENT SILICONE-BASED, NEUTRAL CROSS-LINKING GROUT. FOR INTERIORS AND EXTERIORS AND IN SWIMMING POOLS. IDEAL FOR USE ON FACADES. SUITABLE FOR MARBLE, GRANITE AND NATURAL STONE. ZHERORISK TECHNOLOGY OFFERS VERY LOW VOLATILE ORGANIC COMPOUND EMISSION RATE. Single-component silicone- and oxime-based, neutral cross-linking grout, free from methylethyl ketone oxime. Guaranteed - does not stain the joint edges of natural stone. Does not cause corrosion (rust) on unprotected metal surfaces. ADVANTAGES / FEATURES • Product exhibiths Very low volatile organic compound (VOC). Complies with the most stringent Global Air Quality Regulations. Compatible with natural stone in compliance with ISO 16938-1 • Also available with “structured” colors with a granular surface similar to stone • Also available in "matte” colors • Flexibility • Waterproof • Ready to use • No restrictions for transport over road, sea, air and rail • Excellent resistance to weathering, aging and UV rays • Resistant to mold and bacteria • Highly smoothable surface • Non-corrosive 10.4 U.S. oz. (310 ml) cartridge (boxes with 20 pcs) Sealing of marble and all natural stone, e.g. sandstone, quartz, granite, gneiss, porphyry, etc. in interiors and exteriors. Insulation of expansion joints on floors, walls and facades. Sealing of marble / natural stone swimming pools, including underwater joints. Sealing of profiled and enamelled glass. To bond the outside of mirrors in contact with natural stone. Stress-compensating bonding of natural stone on metal, e.g. stairs on a metal construction The surfaces to be grouted or bonded must be perfectly clean, dry and free of dust, grease, oil and old paint. Cleaning non-porous surfaces: clean with OTTO Cleaner T (drying time about 1 minute) and a dry fiber-free cloth. Cleaning porous surfaces: clean the surfaces mechanically, e..g with a steel brush or a smoothing disc to remove loose particles. Remove the top part of the threaded part of the cartridge, screw in the plastic nozzle and cut it to the right angle depending on the desired diameter and profile. Insert the cartridge in a manual or air gun (with telescopic piston) and extrude the adhesive grout, being careful to avoid the entrainment of air. Once opened, the packages must be used in a relatively short time. The ideal operating temperature for the substrate and grout is between 59°F (15°C) and 77°F (25°C). The joints must be finished within the grout open time. In the case of non-polished natural stone in particular, take care not to soil the areas around the joint because the product residue is difficult to remove. Especially in the case of sensitive, rough and absorbent natural stone surfaces, such as sandstone and limestone, it is

Abrir o catálogo na página 1

recommended to apply an adhesive on the edges of the joints to prevent the seal from being pressed into the surface of the natural stone during polishing. This may cause stains which may not be able to be removed afterwards. Dust deposits on silicone residue can cause further impurities. For smoothing these materials, use the X-GLM silicone smoother for marble (undiluted). Any product residue must be immediately washed off or removed. It is not recommended to use other commonly commercially available smoothing products (e.g. soap detergents) given the tendency to form stains of typical some...

Abrir o catálogo na página 2

Melamine-faced resin slabs Brass Solid surface material Natural stone (marble, granite, etc.) Submerged natural stone (marble, granite, etc.) Polyester Polypropylene (PP) Aerated concrete Plaster Rigid PVC Flexible PVC film Tinplate Zinc, galvanized iron KEY GOOD ADHESION WITHOUT PRIMER NOT SUITABLE RECOMMENDED TEST Linear meters of joint that can be obtained with a 310 ml cartridge Width Width Width Width 1/4" (6 mm) 8 mm (0.31in) 10 mm (0.39 in) 15 mm (0.59in) ± 10 m (32.8 ft) ± 8 m (26.25 ft) ± 6 m (19.68 ft) ± 6 m (19.68 ft) ± 4.5 m (14.76 ft) ± 3 m (9.84 ft) ± 3 m (9.84 ft) ± 2 m (6.56...

Abrir o catálogo na página 3

Powered by TCPDF (www.tcpdf.org) Data detection at temperature +73.4°F (+23 °C ), R.H. 50% and with no wind. May vary depending on the specific conditions of the installation site. Form n. 811 Revision n. 0 Date: March 2021 The information and provisions contained in this technical data sheet reflect our best experience. Given the impossibility of directly intervening on the conditions of the work site and execution of the works, they represent indications of a general nature, which are in no way binding on our Company. It is therefore advisable to perform a spot test to check the...

Abrir o catálogo na página 4

Ottoseal S70 1 / 4Páginas

Excertos do catálogo

Todos os catálogos e folhetos técnicos da LITOKOL

Ottoseal S70
1 / 4Páginas