ZIPABOX 433MHz MODULE
2Pages

QUICK INSTALLATION GUIDE vl.2 ©TRADEMARKS Zipato and the Zipato logo are registered Trademarks. AH other product names mentioned herein may be trademarks or registered trademarks of their respective companies. © NOTICE Although Zipato has attempted to ensure the accuracy of the content of this manual, it is possible that this document may contain technical inaccuracies, typographical, or other errors. Zipato assumes no liability for any error in this publication, and for damages, whether direct, indirect, incidental, and consequential or otherwise, that may result from such error, including, but not limited to loss of data or profits. Zipato provides this publication "as is" without warranty of any kind, either express or implied, including, but not limited to implied warranties of merchantability or fitness for a particular purpose. The published information in the manual is subject to change without notice. Zipato reserves the right to make changes in the product design, layout, and driver revisions without notification to its users. This version of the Installation guide supersedes all previous versions. © ELECTROMAGNETIC COMPATIBILITY When operated according to manufacturer instructions, the product complies with all applicable CE harmonised standards from EMC Directive 2004/108/EC and Part 15 of the FCC Rules. The connections conducting HF signals must not be damaged or altered in any way by the user. © TAKE CARE OF YOUR SAFETY Display extreme caution when using ladders or steps, please follow manufacturer's instructions. Be careful when using hand and power tools and follow the manufacturer's guidelines when using them. Take care that the correct tools are used. Wear goggles or protective clothing where required. ©DANGER RISK OF ELECTROCUTION All work on the device should only be carried out by trained and skilled electricians. Observe the country-specific regulations. ©CAUTION The connected devices and the flush-mounted receiver can become damaged if devices are operated that do not correspond to the technical specifications (see technical data). ©DANGER RISK OF FATAL INJURY FROM ELECTRIC CURRENT. The device has no basic insulation and must therefore be installed in a way that protects against accidental contact. ©DANGER RISK OF FATAL INJURY FROM ELECTRIC CURRENT. When installing a wall plate, the distance between the cover's fixing brackets or screws and the connections of the flush - mounted MM Switch Single must be at least 4 mm once installed. If the distance is less than 4 mm, a deeper installation box must be used. The fixing brackets or screws of the cover must not press against the housing. Only insulated tools may be used for operation on the device, e.g. an insulated phase tester. INTRODUCTION © COMPATIBILITY This Expansion Module is designed to work only with Zipabox. © HANDLING Do not drop, knock or shake the module. Rough handling can break internal circuit boards and connectors. © ENVIRONMENT Do not expose the module to excessive heat or cold, as it can damage or shorten the life of electronic circuit boards. If possible, dispose this module at a recycling center. Do not dispose of this module with the household waste. © TECHNICAL DETAILS POWER SUPPLYFom Zipabox OPERATING TEMPERATURE-10° ~ +40° C OPERATING HUMIDITY5 ~ 95% RH DIMENSIONS29 x 87 x 46 mm (without antenna) WEIGHT62g (with antenna) COMMUNICATION PROTOCOL433 COMMUNICATION RANGE Up to 30m indoor or © UNPACKING Zipabox 433 MHz Module consists of: ■ 1x Expansion Module ■ 1x 433 MHz antenna PLEASE NOTE: Connect antenna by screwing it clockwise to the connector on the module © CONNECTING DEVICE 1 | Disconnect Zipabox from power supply 2 | Align connector of Zipabox 433 Expansion Module to expansion Slot 2 of Zipabox (or to module connected into Slot 2) 3 | Join module and Zipabox together until gap between them is completely closed. 4 | Connect Zipabox to power supply © INSTALLATION/MOUNTING Mount together with Zipabox. ©INTERFERENCE All wireless devices are subject to interference, which could affect device performance. © REPARING Do not attempt to repair this product. There are no user-serviceable parts inside. © WATER-RESISTANCE This product is not water-resistant. Keep it dry Moisture will corrode the inner electronics. © CLEANING Use a dry cloth to clean this product. Do not use harsh chemicals, cleaning solvents or strong detergents. www.zipato.com make your home smart www.zipato.com I 01

ADDING DEVICES TO 433MHZ NETWORK 1 | Go to Zipato Control Center and click on “General” on the left sidebar 2 | Under Device Manager section click on “add new device” button 3 | In popup window search for the 433Mhz device you want to add a) If your device is transmitter (e.g. battery powered wall switch) the clock will start immediately, and you need to initiate joining by clicking on the learn button on the device itself. b) If your device is a receiver (e.g. mains socket / plugin) you will have to put it into a learning mode before you press the “continue” button in the GUI. After you...