Moisture Guard
3Pages

Concrex® Cold Set Concrex® Deep Fill Concrex® Deep Fill Concrex® Acid Technical Data Sheet Strength Rapid Concrex® Sub Zero Concrex® Asphalt Repair Moisture Guard for areas with persistent ® Colours ® Colours humidity, Concrex Concrex Concrex® Deepcondensation Fill Concrex® Coving Cold Set Cold Set Mortar or poor air circulation The curing agent is added to the sand/resin at point of use, and on PARATION mixed the mortar should be used within 15 - 30 minutes dependin d be clean, dry and free of all loose material. Wire brushing Watco Moisture Guard is a high performance, water-based, acrylic paint designed to Areas of use: temperature. generally sufficient. Watco Bio-D degreaser can be used to enhance and protect interior surfaces. It is ideal for areas with persistent humidity, • For areas with persistent humidity, If the entire pack of Watco Concrex® Carbon Fibre cannot be used w and oil. If the surface is damp it can be primed with Watco constant temperature fluctuations, insufficient air movement, or other environmental condensation or poor air circulation 30 minutes, mixed. To split a basements, pack carefully conditions, which can attack the paint film resulting in mould and mildew growth.* it can be partsuch as bathrooms, and halve the (ideally measured by weight), andasuse the number kitchens, wellhalf as, areas where of curing ag Do not mix inside the plastic bucket. Tip the sand/resin into a mixi Moisture Guard is extremely easy to mix and apply with no sanding or primer needed. mould or mildew are a concern ent of Watco Concrex® Carbon Fibre is very high. This means on a board. The satin finish is also scrubbable and moisture resistant, making it easier to keep your s not usually required when filling holes in concrete floors or surfaces clean for the foreseeable. Shake the bottles of curing agent thoroughly until the liquid is a un Suitable for: ugh or damaged concrete. Watco Tack Coat adhesive primer is Form the sand/resin into a mound leave a small • Suitable forand a wide range of newhole or in the mi when using Concrex® Carbon Fibre as a thin section screed Empty the curing agent into the hole, ensuring the bottles are com previously painted surfaces including urfaces. It is also recommended when repairing intricate/high drywall, concrete, plaster, wood, drained. uch as broken floor joint edges, and damaged step nosings. metal andthe ceramic tilesagent using a trowel u Carefully mix the aggregate with curing smooth mortar is obtained, this will take several minutes. The mor the mixing, the ‘wetter’,Features: smoother and more manageable the mix b ve gloves. • Protects the dried coating from fungal Alternatively, you can knead the mixture by hand wearing suitable the sand are already pre-blended and is supplied with bottles of degradation important to mix thoroughly until you achieve a consistent colour x 100ml in the 10kg pack and 2 x 500ml in the 25kg pack. • Resists cracking, peeling and A ‘Cretangle’ or suitable open pan mixer can be used to mix large q blistering • No sanding or primer required, low odour • Washable, moisture resistant finish • Scrubbable finish to Class 1 Wet Scrub Rating (ISO11998) • Fast drying - apply a second coat in 2 hours ttles of curing /resin White (Satin) agent Mix thoroughly using a trowel (or by hand – it’s easier) * Moisture Guard contains a biocide to protect the dry film from fungal degradation.Once dried the paint is classed as a treated article and contains a surface biocide 4,5-dichloro-2-noctyl-4- isothiazoline-3-one. Trowel firmly into the repair Wipe the trowel with wh to get a good finish For repairs deeper than 50mm apply in separate layers allowing 6 between layers, or use Concrex® Deep Fill which can be applied at rtar firmly into the repair andSpeak finish with trowel or float. To Need help? toathe experts - 100mm in one layer. ooth finish, regularly wipeand the surface ofteam the are trowel cloth Our dedicated professional here with to helpa you get the15mm best results for yourthick project. h white spirit. They will talk you through the preparation and application stages when using Moisture Guard. SAFETY x® Carbon Fibre is normally applied at 5mm - 50mm thick, Material Safety Data Sheets are available. n be feather-edged if most of the repair is at least 5mm thick. Call our expert team on: 01483 418 418 Watco UK Ltd, Eastgate Court, 195-205 High Street, Guildford, Surrey, GU1 3AW Tel: 01483 418 418 www.watco.co.uk E-mail: sales@watco.co.uk,

Preparation & Application Moisture Guard for areas with persistent humidity, condensation or poor air circulation 1 Surface Preparation Remove any dust, dirt or grease from the surface. Watco Bio-D can be used to remove grease and oil from painted surfaces. If painting over an existing coating, abrade to remove any loose paint. Check the remaining paint is well bonded. Ensure the surface is completely dry before painting, moisture content of the substrate should be below 16%. Remove any mould or mildew from the surface. If you are concerned about concerned about mould and mildew behind...

Technical Data Sheet Moisture Guard for areas with persistent humidity, condensation or poor air circulation Specification Composition Water-based acrylic. Recommended number of coats 2 coats are recommended. Coverage may vary depending on the profile, porosity of the substrate and application method. Usage Interior/Exterior Application Tools Approx. 10m2 per litre, per coat. Overcoat Times Recoat after 2 hours. Curing Time Touch dry in 30 minutes, fully cured after 7 to 10 days. New or previously painted drywall, plaster, cement, concrete, ceramic tile, primed or previously painted wood...