Catalog excerpts
LIQUID-APPLIED WATERPROOFING ELASTIC SYSTEMS PLASTIVO 250 PRODUCT DESCRIPTION PLASTIVO 250 is a waterproof coating featuring high elasticity and versatility of use to waterproof surfaces subject to positive and negative hydrostatic pressure. PRODUCT APPLICATION Positive and negative hydrostatic pressure waterproofing of structures made of concrete, cement blocks or mixed masonry, previously levelled with suitable VOLTECO mortars, affected by moderate settlements and/or movements. Particularly suitable for: • Walls and foundations slabs and reinforced concrete floors • Surfaces and structures exposed to contact with water • Tanks, channels and structures also intended to contain drinking water, reinforced concrete foundation walls, pools, etc • Garages, cellars, underground structures in general, tanks, channels and pools • Easy and quick application • Applicable by brush, roller and spatula • Excellent impermeability in conditions of positive and negative hydrostatic pressure • Excellent elasticity • Adheres to different types of surfaces (concrete, brickwork, brick, gypsum board, plastic, metal, ceramic, polystyrene, wood, other) • Complete waterproofing cycle within one day • Low environmental impact thanks to reduced CO emissions, very low Volatile Organic Compound emissions (VOC), components obtained from recycling processes • The product helps earning points for LEED certification Preparing the surfaces Verify the structure suitability for the hydrostatic loads; if intended to contain water, perform a preload test.
Open the catalog to page 1LIQUID-APPLIED WATERPROOFING ELASTIC SYSTEMS PLASTIVO 250 Remove any dirt, oil, paint and any material or deposit that could compromise adhesion of PLASTIVO by pressure blasting, sandblasting or bush-hammering lightly. The surface that is to be treated must be solid and perfectly clean from cement slurry. Repair the surface with suitable VOLTECO mortar if the surfaces are very uneven, have gravel nests or in the case of mixed masonry. If the surfaces are old and/or dusty or partially soaked with water, apply PROFIX 30 or PROFIX 60 primer (see the related technical data sheets) with a...
Open the catalog to page 2LIQUID-APPLIED WATERPROOFING ELASTIC SYSTEMS PLASTIVO 250 expansion joints. Curing When waterproofing foundation walls, let it cure for at least 24 hours after application before backfilling. When coating the waterproofing with any type of protective layer or finish (ceramic coating, protective screed, plaster, cement-based levelling compound, plastic drainage, etc.), let it cure at least 3 days after application. When waterproofing structures intended to contain water, allow a curing phase of at least 7 days once the product is applied. The curing times can be longer in the presence of a...
Open the catalog to page 3LIQUID-APPLIED WATERPROOFING ELASTIC SYSTEMS PLASTIVO 250 Specification Specific weight Liquid/powder mixing ratio Specification Bond strength Capillary absorption Test method Water vapour permeability (equivalent thickness: Sd) Permeability to CO₂ (Sd: equivalent thickness) Declared performance (*) Certified performance (**) ≥ 0,8 MPa Crack Bridging Ability Crack Bridging Ability (product + Flexonet mesh) Thermal compatibility Part 1 (adhesion after UNI EN 13687-1 50 un/freezing cycles) Test method Crack Bridging Ability (+23°C) Crack Bridging Ability (+23°C) (product + Flexonet mesh)...
Open the catalog to page 4LIQUID-APPLIED WATERPROOFING ELASTIC SYSTEMS PLASTIVO 250 The quoted data are obtained in a laboratory at +20°C and 60% RH. * Performance thresholds guaranteed by VOLTECO ** Performance values certified by accredited third parties SAFETY This is a non-toxic alkaline product. It is recommended to use a mask and gloves while working. In case of accidental contact with eyes, wash thoroughly with water and seek medical attention. Via delle Industrie, 47 - 31050 Ponzano Veneto (I) Via delle Industrie, 47 - 31050 Ponzano Veneto (I) 10 0003-CPR-2015/03/31 EN 1504-2:2005 PLASTIVO 250 Protection...
Open the catalog to page 5All VOLTECO catalogs and technical brochures
-
X-RAPID BIANCO
3 Pages
-
SISTEMA BI FLEX
4 Pages
-
VOL-TEC
3 Pages
-
X-LIME
3 Pages
-
Depliant Amphibia Volteco
9 Pages
-
AQUASCUD LINE
3 Pages
-
BI MORTAR CONCRETE SEAL
4 Pages
-
BI MORTAR RASO SEAL
3 Pages
-
AQUASCUD 500
3 Pages
-
FLEXOMIX 30
3 Pages
-
WT 102
2 Pages
-
VOLGRIP TC
3 Pages
-
VOLGRIP LH
3 Pages
-
VOLGRIP HP
3 Pages
-
VOLCLAY PANELS VP1 and VP1F
2 Pages
-
TRIPLEZERO-T
2 Pages
-
TAP 3
2 Pages
-
SPIDY 15
2 Pages
-
REVOMAT
2 Pages
-
REPOSOL
2 Pages
-
PROFIX 60
3 Pages
-
PROFIX 30
3 Pages
-
PROFIX 20
2 Pages
-
PROCLEAN
2 Pages
-
PLASTIVO 180
5 Pages
-
PLASTIVO 300
5 Pages
-
PAINT PROTECTION
3 Pages
-
PAINT POOL
4 Pages
-
PAINT FLOOR
3 Pages
-
PAINT AIR
3 Pages
-
MICROLIME NOVECENTO
2 Pages
-
MICROLIME GEL
2 Pages
-
JOIN BT
2 Pages
-
GARVO 3 and 5
2 Pages
-
FLEXONET
2 Pages
-
BREAK
2 Pages
-
BI MORTAR SL
3 Pages
-
BI MORTAR
3 Pages
-
BI FLEX SYSTEM
3 Pages
-
BARRIER
3 Pages
-
AQUASCUD SYSTEM 430
4 Pages
-
AQUASCUD SYSTEM 420
4 Pages
-
AKTI-VO 201
2 Pages
-
ADEKA KM
3 Pages
-
FLOWMIX 70
3 Pages
-
FIBROMIX 40
3 Pages
-
FIBRO 20
3 Pages
-
CP2
4 Pages
-
CP0
4 Pages
-
CALIBRO NHL
3 Pages
-
CALIBRO PLUS EVAPORATION
3 Pages
-
PROFIX 40
3 Pages
-
SANOFER
2 Pages