LIQUID-APPLIED WATERPROOFING ELASTIC SYSTEMS PLASTIVO 180 PRODUCT DESCRIPTION PLASTIVO 180 is a polymer-modified two-component thixotropic flexible waterproofing coating with CORE CURING TECHNOLOGY for an effective curing both in presence of low temperatures and partially damp surfaces It is made of aggregates, cement-based binders and acrylic polymers in emulsion. It is suitable for the containment of drinking water (M.D. 174). PRODUCT APPLICATION For negative/positive hydrostatic pressure waterproofing of wall surfaces, previously levelled with suitable VOLTECO mortars, or concrete, affected by slight settlements and/or movements. Particularly suitable for: • Surfaces and structures exposed to contact with water • Balconies • Ledges, concrete gutters, flower boxes (set-up anti-root protection beforehand) and wells • Tanks, channels and structures also intended to contain drinking water, reinforced concrete foundation walls, pools, etc • All indoor surfaces such as kitchens, bathrooms and showers even if made of gypsum board • Dry floors • Quick curing that permits short application times between first and second layer and tiles application, even in the presence of low temperatures (within 48 hours) • Effective curing on set surfaces, even partially wet • Reduced risks caused by after application with rain, fog, other • Suitable for contact with drinking water • Anticarbonation protection with ”barrier” function • Elastic up to -5°C • Adheres to different types of surfaces (concrete, brickwork, brick, gypsum board, plastic, metal, ceramic, polystyrene, wood, other) • Low environmental impact thanks to reduced CO emissions, very low Volatile Organic Compound emissions (VOC), components obtained from recycling processes • The product helps earning points for LEED certification Preparing the surfaces Verify the structure suitability for the hydrostatic loads; if intended to contain water, perform a preload test. Remove any dirt, oil, paint and any material or deposit that could compromise adhesion of PLASTIVO by pressure blasting, sandblasting or bush-hammering lightly. The surface that is to be treated must be solid and perfectly clean from cement slurry. Repair the surface with suitable VOLTECO mortar if the surfaces are very uneven, have gravel nests or in the case of mixed masonry. If the surfaces are old or dusty, apply PROFIX 30 primer with a roller, a brush or by spray (see related technical data sheet).

LIQUID-APPLIED WATERPROOFING ELASTIC SYSTEMS PLASTIVO 180 For surfaces not totally dry but in which curing process is completed surface humidity must not be higher than 8% (measured with a Storch electric hygrometer). Construction joints, spacers, cracks and joints (positive hydrostatic pressure) Connect the construction joints between the bed and the vertical wall by forming a 3x3 cm fillet with SPIDY 15 rapid-setting mortar. Remove the spacers on both sides of the wall and plaster with SPIDY 15 rapid-setting mortar. Connect all joints, any significant cracks and vertical or horizontal edges...

LIQUID-APPLIED WATERPROOFING ELASTIC SYSTEMS PLASTIVO 180 contact with water. Finishing When applied indoors, it is recommended to coat the walls with the macroporous CALIBRO as an anticondensation layer. It is also possible to complete the finish with X-LIME. The product can be finished with PAINT FLOOR or PAINT POOL (see the related technical data sheets) or ceramics, depending on the intended use. Ceramics must be laid with a large grout gap and C2-type adhesive (preferably with an S1 and S2 deformation class). The subsequent finishing plaster must be applied with CG2 class sealant cement-based...

LIQUID-APPLIED WATERPROOFING ELASTIC SYSTEMS Test method Crack Bridging Ability (product + Flexonet mesh) Declared performance (*) Certified performance (**) Test method Performance requirements Declared performance (*) Crack Bridging Ability (+23°C) Crack Bridging Ability (-5°C) Crack Bridging Ability (+23°C) (product + Flexonet mesh) Crack Bridging Ability (-5°C) (product + Flexonet mesh) Initial adhesion Adhesion after immersion in water Adhesion after heat application Adhesion after un/freezing cycles Tensile adhesion strength after contact with UNI EN 14891 Met. A.6.7 chlorinated water Adhesion...

LIQUID-APPLIED WATERPROOFING ELASTIC SYSTEMS Via delle Industrie, 47 - 31050 Ponzano Veneto (I) Via delle Industrie, 47 - 31050 Ponzano Veneto (I) 10 0001-CPR-2015-09-01 EN 1504-2:2005 PLASTIVO 180 Protection systems of the concrete surface. Coating against the risks of penetration (PI), humidity control (MC) and increased resistivity (IR) PLASTIVO 180 Two-component liquid waterproofing product modified with polymer (CM 01) for outdoor applications and in pools under ceramic tiles(applied with class C2 adhesive in compliance with EN 12004) Reaction to fire: Class E Water vapour permeability:...