Catalogs >
VOLTECO >
CP0

CP0
4Pages

Catalog excerpts

PROTECTIVE WATERPROOF LEVELLING COMPOUNDS CP0 is a thick mineral organic finish coating for outdoor and indoor use, featuring high breathability and water resistance, composed of water-dispersed acrylic-siloxane resins with a final coarse appearance. CP0 features flexibility performance that can be enhanced when used in combination with CP1/CP2 levelling products and FLEXONET elastic mesh. PRODUCT APPLICATION Protection and finish of walls in general, both outdoors and indoors. Particularly suitable for: • Cement-based or lime plasters, both new and well-cured or old and well-adhered to surface • Light plasters and thermo-insulating plasters, as well as absorbent and non-absorbent • Surfaces with synthetic finishes or plastic paint • Exterior insulation systems, on either on relative reinforced levelling or on existing finishing coats • Concrete surfaces • Finishing of systems CP1 and CP2 or X-LIME and X-RAPID • Excellent water repellency • Good breathability • Good flexibility, especially in combination with CP1/CP2 and FLEXONET • Excellent adhesion to both mineral supports and painted surfaces • Fine aesthetic appearance, coarse and coloured effect • Compact effect, excellent filling and covering capability • Resistant to the formation and proliferation of mould, algae and fungi • Long-lasting thanks to high resistance to atmospheric agents and UV rays • Practical package, ready to use Surfaces with the presence of mould, algae and fungi Thoroughly high-pressure clean the surfaces to remove any micro-organisms, wait for them to dry and apply an undiluted coat of PROCLEAN disinfectant treatment (see relative data sheet), then wait at least 2-3 hours before applying the base product of the following coating. Surfaces with the presence of evident cracks or widespread micro-lesions If there are evident cracks preventively apply the special flexible FLEXONET mesh, as a reinforcement strip, by embedding it in a layer of CP1 or CP2, having previously grinded a groove in

Open the catalog to page 1

PROTECTIVE WATERPROOF LEVELLING COMPOUNDS CP0 the substrate across the cracks. With widespread micro-cracks it is possible to apply the FLEXONET mesh over all the surfaces, embedding it in a layer of CP1 or CP2, taking care to position the sheets lined up next to each other without overlapping them. It is possible to apply a second coat of CP1 or CP2 to improve the elastic performance of the cycle. Surfaces coated with X-LIME/X-RAPID, with CP1/CP2 or new levelling in general Wait for complete curing, then clean any build-up or dust from the surface by brushing or lowpressure washing. When...

Open the catalog to page 2

PROTECTIVE WATERPROOF LEVELLING COMPOUNDS Consumption can vary based on absorption and irregularity of the surface: with a homogeneous surface it is approximately 2.2-2.4 kg/m². CP0 is packed in 25 kg pails. The product must be stored in a dry place without being exposed to frost and heat (maximum temperature: 40°C) or direct exposure to the sun before being applied. WARNINGS - IMPORTANT NOTES The recommended ambient conditions for application are at a temperature between +5°C and 30°C, with maximum relative humidity of 70%. Do not apply the product in direct sunlight. The presence of wind...

Open the catalog to page 3

PROTECTIVE WATERPROOF LEVELLING COMPOUNDS CP0 VOLTECO S.p.a Via delle Industrie, 47 - 31050 Ponzano Veneto (I) 15 0026-CPR-2015/05/05 EN 15824 CP0 Outdoor and indoor plaster with organic binders. Water vapour permeability: Class V2 Water absorption: Class W3 Adhesion: ≥ 0.3 MPa Thermal conductivity: (λ10,dry) 0.83 W/m·k (value table; P = 50%) Durability: NPD Reaction to fire: Euroclass F Hazardous substances: See SDS © Copyright Volteco SpA - All rights reserved. Information, Images and text found in this document are exclusive property of Volteco SpA. They may change anytime without prior...

Open the catalog to page 4