HOME CONTROL Vitrum On-Off UUireless

INDEX 0. Before starting. . . . . . . . . . . . . . . . . 3 1. Electrical connections. . . . . . . . . . . . 4 2. Positioning the glass decor panel. . . . 8 3. Vitrum is intelligent . . . . . . . . . . . . . 9 4. Configuration of the type of switch. 12 5. Advanced functions. . . . . . . . . . . . 15 6. Factory reset. . . . . . . . . . . . . . . . . . 19 7. Supervision. . . . . . . . . . . . . . . . . . . 21 8. Compatibility. . . . . . . . . . . . . . . . . 22 9. Compliance with ec directives . . . . 22 Main technical specifications. . . 23

0. BEFORE STARTING The Vitrum system that you have purchased is designed for connection to your existing 240V power supply circuit. Before commencing installation, ensure that the mains power supply had been disconnected by setting the main switch on your electricity meter to OFF. Do not re-connect the power supply and start using Vitrum until all connections have been correctly completed and the Vitrum unit has been inserted into the wall-mounting box. Vitrum must be installed by a professional electrician who is qualified to operate on electrical power circuits in full compliance with all current...

1. ELECTRICAL CONNECTIONS Simply connect the Live wire to the terminals marked “L”,”C1...C3”and the Neutral wire to the terminal marked “N” and the light(s) to the terminal(s) marked “NO 1...NO 3”. All the relays function as switches, and the contacts are normally open. The device may be set to operate as a “Button” as well as a “Switch”. On-off Wireless 1 channel EU 4 On-off Wireless 2 channels EU

On-off Wireless On-off Wireless On-off Wireless

On-off Wireless On-off Wireless The circuit diagram below jumper in order to replace a button which controls a step relay for control of an existing lighting system: Step Relay

IMPORTANT Fit a rapid-acting fuse with a high switching capacity that is suitable for the load applied to the device. Recommended fuse to put in series for each channel is: fastacting ceramic body cartridge fuse mod. F4AH250V (800W); F6,3AH250V (1500W); F12,5AH250V (2400W); F16AH250V (4x800W). Devices are built to fit italian “503” boxes, 3 modules, comply with the standard IEC/EN 60670-1 and dimensional tab A8 of standard CEI 23-74:2002; 1-gang British Standad boxes, 2 modules, comply with the standard 4662:2006. After connecting, check that the wires are correctly positioned inside the wallmounting...

2. POSITIONING THE GLASS DECOR PANEL In order to refit the glass panel correctly, ensure that the four plastic tabs on the panel are in perfect alignment with the anchor holes. When the glass panel tabs are aligned with the holes, press the four corners of the glass panel evenly until it is fully inserted into the wall-mounting box. After fitting the glass panel, the buttons remain inoperative for about 10 seconds. An acoustic signal sounds three times to indicate that the sensors have been recalibrated, after which they resume normal operation. To remove the glass panel from the wall-mounting...

3. VITRUM IS INTELLIGENT The product that you have purchased functions INDEPENDENTLY, but it also has a hi-tech “Wireless” technological heart. Thanks to “Z-Wave” Wireless technology, each Vitrum Wireless unit offers numerous advantages if connected as part of a network: it is possible to associate multiple Vitrum units, to construct scenarios, and to control lights using a remote control unit. If you connect Vitrum into a preexisting z-wave net working with third parts devices, please refer to instruction and procedure of your remote control. Otherwise proceed as follows to include Vitrum to...

Press and hold down "INC" until the corresponding LED turns yellow, then Place the HOME MASTER remote handset near the Vitrum unit to be included n the network. Touch any of the keys on Vitrum to include the unit in the home wireless network Vitrum indicates that it has been connected to the network by flashing the yellow LEDs three lights connected to the unit

• When all the Vitrum units have been added to the network, press the “INC” key again until the LED switches off. Now you will see that the illuminated rings around the Vitrum touch keys no longer light red when changing from one status to the next. NotE A Vitrum unit cannot be added to the network if it has already been included in a different network. In this case, it is necessary to perform the factory reset procedure > see Paragraph 6. 11

4. CONFIGURATION OF THE TYPE OF SWITCH Vitrum is configured to operate as a normal ON/OFF switch (i.e. to ‘toggle’ the ON and OFF status with each touch). The individual channels can be configured as simple buttons. To do so, proceed as follows: • Remove the glass décor panel. • Press and hold down the two service touch keys for at least 8 seconds and wait until the BEEP sounds twice to indicate that the system has entered the configuration menu. The LEDs in the touch keys will begin to flash either blue or red, depending on the setting entered. The default setting for the flashing light is blue...

• Press each of the Vitrum touch keys briefly to select the desired operating mode. FLASHING BLUE Switch FLASHING RED Button Each time the touch key is pressed, the cyclic status is ‘toggled’: Switch -> Button -> Switch … 13

Vitrum returns to normal operation after 12 seconds of inactivity or if the two service touch keys indicated by the yellow arrows in the figure below are pressed briefly (0.5 seconds). IMPORTANT The default operating mode is “Switch”. 14

5. ADVANCED FUNCTIONS: CREATION OF CONTROL LOGIC On all Vitrum Wireless units, it is possible to create control logic processes that associate the button on one Vitrum module to other buttons on OTHER Vitrum modules (up to a maximum of five). Every Vitrum Wireless On-Off supports a number of groups equal to the number of the device’s channels (=device’s buttons); every single button/channel of a Vitrum has its own association group. For creating a control logic, the modules must first be included in the home wireless network (see paragraph 3). Then proceed as follows: • Set the HOME MASTER remote...