EN H O M E C O N T R O L Vitrum Master on-off Wireless INSTALLATION and OPERATION

DeSCRIPTION INDEX A Vitrum Scene differs from Dimmer and On-Off devices for this reason: there is no exit used for directly control a load. It’s used for creating lighting scenarios in your house: simply pressing a button, you can switch on and off (in case of lamp connected to a Vitrum dimmer you can select the light level too) the lights of your scenary. 0. Before starting. . . . . . . . . . . . . . . . . 3 1. Electrical connections. . . . . . . . . . . . 4 2. Positioning the glass decor panel. . . 6 3. Vitrum is intelligent . . . . . . . . . . . . . 8 4. Advanced functions. . . . . . . . ....

0. BEFORE STARTING The Vitrum system that you have purchased is designed for connection to your existing 240V power supply circuit. Before commencing installation, ensure that the mains power supply had been disconnected by setting the main switch on your electricity meter to OFF. Do not re-connect the power supply and start using Vitrum until all connections have been correctly completed and the Vitrum unit has been inserted into the wall-mounting box. Vitrum must be installed by a professional electrician who is qualified to operate on electrical power circuits in full compliance with all current...

1. ELECTRICAL CONNECTIONS Electrical connections with neutral wire: connect the Live wire to the terminal marked “L”, the Neutral wire to the terminal marked “N”: 4

IMPORTANT After connecting, check that the wires are correctly positioned inside the wallmounting box. When securing Vitrum to the wall-mounting box, use the screws supplied and note that the maximum torque to be used when tightening the screws in the embedding box is 0.8 Nm. In addition, the surface of the wall for at least 2 cm surrounding the embedding box must be as flat and smooth as possible, and must not have any rough patches and/or bumps that protrude more than 1 mm. If the screws are not tightened with the torque specified, or if the embedding box is installed on unsuitable surfaces,...

2. POSITIONING THE GLASS DECOR PANEL In order to refit the glass panel correctly, ensure that the four plastic tabs on the panel are in perfect alignment with the anchor holes. When the glass panel tabs are aligned with the holes, press the four corners of the glass panel evenly until it is fully inserted into the wall-mounting box. Anchor holes on electronic section 6

After fitting the glass panel, the buttons remain inoperative for about 10 seconds. An acoustic signal sounds three times to indicate that the sensors have been recalibrated, after which they resume normal operation. To remove the glass panel from the wall-mounting box, gently lever the upper or lower edge away Anchor holes on décor panel 7

3. VITRUM IS INTELLIGENT The product that you have purchased functions when included in a Z-Wave wireless net. Thanks to “Z-Wave” Wireless technology, each Vitrum Wireless unit offers numerous advantages if connected as part of a network: it is possible to associate multiple Vitrum units, to construct scenarios, and to control lights using a remote control unit. If you connect Vitrum into a pre-existing z-wave net working with third parts devices, please refer to instruction and procedure of your remote control. Otherwise proceed as follows to include Vitrum to your Home Wireless Network: • Open...

• Press and hold down “INC” until the corresponding LED turns yellow, then release the button. Place the HOME MASTER remote handset near the Vitrum unit to be included in the network. Touch any of the keys on Vitrum to include the unit in the home wireless network. Everytime a new device is included into the zwave net, you must include your Vitrum scene again; during this operation, Vitrum scene will blink of magenta color for few seconds: wait until it stop to proceed. 9

Dopo esservi assicurati di aver incluso tutti i dispositivi z-wave della rete, avvicinatevi con il telecomando HOME MASTER al Vitrum Master on-off da includere e toccate il suo tasto. • When all the Vitrum units have been added to the network, press the “INC” key again until the LED switches off. Now you will see that the illuminated rings around the Vitrum touch keys no longer light red when changing from one status to the next. NotE A Vitrum unit cannot be added to the network if it has already been included in a different network. In this case, it is necessary to perform the factory reset...

4. ADVANCED FUNCTIONS: CREATION OF CONTROL LOGIC On all Vitrum Wireless units, it is possible to create control logic processes that associate the button on one Vitrum module to other buttons on OTHER Vitrum modules For creating a control logic, the modules must first be included in the home wireless network -> see paragraph 3. Using Vitrum master on-off you can have two different situations: 1-Vitrum master on-off is used only for switching all the lights/blind shutters of your house off: in this case you only need to include it last into your net. So every time you push its button, Vitrum master...

To do it proceed as follows: • Set the HOME MASTER remote handset to association mode by presssing and holding down the “ASC” button until the yellow LED lights. Then release the “ASC” button. • Press the buttons of the other Vitrum that are physically connected to the lighs you want to be part of the scene. The LED corresponding to the selected button/ channel will flash magenta until the ‘association’ process has been completed. When finished press briefly again the ASC button of remote control 12

• Now press the button of your Vitrum Master on-off. Now, after having switched off everything, at second touch Vitrum master on-off will switch all the associated Vitrum on (at same level of light they had before being switched off). The illuminate ring will be yellow. In order to cancel associations that have been entered, simply perform the same procedure, though pressing the “DIS” key on the HOME MASTER remote handset instead of “ASC”. 13