Vitex with TeflonTM Vinyl emulsion paint with surface protection technology Premium quality & washability vinyl paint with matte finish for interior use designed with Teflon™ surface protection technology. Teflon™ technology creates a paint surface protection, which gives enhanced resistance to the absorption of common household stains, and makes it easier to remove stains after a long period of time. Teflon™ technology creates an anti-static protection surface that reduces the deposition of dust, smoke and other pollutants. Removing stains is done with a soft damp cloth and soap or non-abrasive mild household cleaners. Vitex with Teflon™ emulsion paint can be applied on properly prepared surfaces of any material. It has very good levelling properties, hiding power, and resistance to frequent washing (Class 1, EN 13300/ISO 11998), coupled with superior whiteness and performance. It is practically odorless in its application because it does not contain ammonia. It is recoatable with any emulsion/acrylic paint of Vitex. Teflon™ branded products have been tested and accredited by Chemours for the stain resistant and easy to clean performance of common household stains. • • • • • New generation emulsion paint with TeflonTM technology Superior performance & stain protection Easy to clean without any residue Antistatic surface that repels dust/smoke Great hiding power and spreading rate COLOURS Available in white and thousands of shades through Vitex’s Colorfull Tinting System. PACKAGING White Bases SPREADING RATE 15 - 18 m2/L per coat on properly prepared surfaces. SURFACE PREPARATION Surfaces should be smooth, clean and dry, free from grease, dust, loose or flaking paint. To fill any cracks or holes use Acrylic Putty or Visto. Surfaces previously covered with water paints or distempers (lime wash or ceiling white) should be primed with Acrylan Unco Eco or Durovit. New surfaces made of plaster, concrete, cement, plasterboard, etc. should be first primed with 100% Acrylic Primer or Acrylan Unco Eco or Blanco Eco. Surfaces stained from smoke, graffity, coffee or any other kind of stain should first be primed with Blanco Eco or Vitosin. APPLICATION Stir well before use. Apply two coats by roller, brush or airless spray gun diluted up to 10% with water. Do not apply at temperature below 5°C, above 35°C and/ or relative humidity above 80%. It is touch-dry after 30-60 minutes and can be recoated after 3-4 hours. Drying time depends on weather conditions (humidity and temperature). Allow at least 2 weeks before cleaning and washing newly painted surfaces with Vitex with Teflon™. Wash gently with water using a soft sponge. In case of bad stains, use a mild colourless detergent or soapy water. Tools must be cleaned immediately after use with water and if needed with soapy water or a detergent. VOC (Volatile Organic Compounds) CONTENT EU maximum VOC content limit values (Directive 2004/42/CE) for this product (category A/a “Interior matt walls and ceilings (Gloss<25@60o)”, Type WB): 30 g/L. This product contains maximum 15 g/L VOCs (ready for use). Teflon™ is a trademark of THE CHEMOURS COMPANY FC, LLC used under license

Vitex with TeflonTM Vinyl emulsion paint with surface protection technology TECHNICAL CHARASTERISTICS Viscosity STORAGE Containers must be kept closed in a cool, dry, well ventilated area protected from direct sunlight at temperatures between 5°C - 38°C. SAFETY ADVICE Read label before use. For further instructions - precautions see Material Safety Data Sheet. Τ.Θ. 139 Ημερος Τόπος, Ασπρόπυργος Τ.Κ. 193 00 P.O. Box 139 Imeros Topos, Aspropyrgos GR 193 00 T. + 30 210 5589 500, F. + 30