X^VIDEX \ TECHNOLOGY FOR THE FUTURE VIDEOKIT VRVK SERIES "6 Wire" bus one way, two way vandal resistant videokit We recommend This equipment is installed by a Competent Electrician, Security or Communications Engineer.

VRVK/6358 Series Vandal Resistant “6 wire Bus” videokit NOTES AND SUGGESTIONS • All diagrams refer to all kits versions: flush or surface. • Dashed connections refer to optional connections (“Local bell”, “Push to exit” & “Door monitor”). • Some diagrams show how to connect a 12Vdc electric lock: these directions are suitable for all diagrams in this manual. • Each time a setting is changed on a videophone (address, extension, number of rings etc.), the videophone must be disconnected from the relevant connection board then after a few seconds reconnected again to allow the recognizing of the...

VRVK/6358 Series Vandal Resistant “6 wire Bus” videokit System components and available versions VRVK/6358 Colour videokit. OUTDOOR STATION 135,0 INDOOR STATION Videophone Art. 6358 pag. 17 ACCESSORIES Power supply Art. 850K pag. 5 Video distributor Art. 316N pag. 21 Flush Mounting Surface Mounting VRVK-1/6358 - flush mounting 1 Outdoor station composed of: 1 Art. VR4KCM: Camera unit 1 Art. VR4KAMK-1: 1 button speaker unit 1 Art. 4852: Flush mounting box VRVK-2/6358 - flush mounting 1 Outdoor station composed of: 1 Art. VR4KCM: Camera unit 1 Art. VR4KAMK-2: 2 button speaker unit 1 Art. 4852:...

™\^VIDEX \ THE POWER TO SECURE VRVK/6358 Series Vandal Resistant "6 wire Bus" videokit OUTDOOR STATION Camera unit Art. VR4KCM pag. 7 INDOOR STATION Videophone Art. 6358 pag. 17 ACCESSORIES Power supply Art. 850K pag. 5 Flush Mounting Surface Mounting

VRVK/6358 Series Vandal Resistant "6 wire Bus" videokit ®0\ vxVIDEX THE POWER TO SECURE CONNECTION TO MAINS The system must be installed according to national rules in force, in particular we recommend to: • Connect the system to the mains through an all-pole circuit breaker which shall have contact separation of at least 3mm in each pole and shall disconnect all poles simultaneously; • The all-pole circuit breaker shall be placed for easy access and the switch shall remain readily operable. POWER SUPPLY INSTALLATION • Remove the terminal side covers by unscrewing the retaining screws; • Fix...

vxVIDEX THE POWER TO SECURE VRVK/6358 Series Vandal Resistant "6 wire Bus" videokit Troubleshooting guide In case of system failure, try the following preliminary checks: • Check that the cables are connected as shown in the installation diagram and that the cables are firmly fixed into the relevant terminals; • Check that the mains voltage is available on terminals 230Vac (or 127Vac) and 0 of the power transformer Art. 850K; • Check the 24Vac voltage output of the power transformer Art. 850K. If this voltage is not available it could be the 1,6A fuse, in this case remove the mains voltage, remove...

VRVK/6358 Series Vandal Resistant "6 wire Bus" videokit ®0\ vxVIDEX THE POWER TO SECURE Rev.0.2 LEGEND ® Camera and illumination LED's ® Video signal mode jumper © Camera switching on mode jumper © Terminals Fig. 1 Front DESCRIPTION 4000 Series vandal resistant camera module (Brushed 2.5mm 12 gauge stainless steel fascia). The Art. VR4KCMC includes a colour CMOS high quality wide angle camera. The wide camera has a horizontal viewing angle of 170 degrees. The white light illumination LEDs are mounted around the camera. The Art. VR4KCMC can be used in video door entry systems: traditional (combined...

™\^VIDEX \ THE POWER TO SECURE VRVK/6358 Series Vandal Resistant "6 wire Bus" videokit Art. VR4KCMC Camera module CONNECTION TERMINALS SIGNALS TECHNICAL SPECIFICATION Working voltage: 12Vdc/24Vdc Power consumption while operating: 100mA Working Temperature: -10 +50°C CLEANING OF THE PLATE Use a clean and soft cloth. Use moderate warm water or non-ag gressive cleansers. Do not use: • abrasive liquids; • chlorine-based liquids; • metal cleaning products.

VRVK/6358 Series Vandal Resistant "6 wire Bus" videokit ®0\ vxVIDEX THE POWER TO SECURE DESCRIPTION Vandal resistant speaker unit specific for VRKV series 6 wire bus videokits. ® Loudspeaker © Yellow LED © Red LED © Green LED © Call button AVAILABLE VERSIONS LEGEND © Microphone volume © Loudspeaker volume © 4 way dip-switch © Jumpers © Connection terminals (m) Button wires Art.VR4KAMK-1NP Microphone volume Adjust the microphone volume. Rotate clockwise to increase or anti-clockwise to decrease Loudspeaker volume Adjust the loudspeaker volume. Rotate clockwise to increase or anti-clockwise to...

Art. VR4KAMK Speaker unit \_the power to secure SETTINGS (DIP-SWITCH & JUMPERS) 4 WAY DIP-SWITCH First two switches are used to set the speaker unit address: the speaker unit address is required for camera recall operation on 2 or more entrance systems. The "door-open" relay can operate either as "dry contact" or "capacitive discharge" mode. • In "dry contact" operation mode the relay works in a traditional way, a power supply or a power source is needed to operate the lock (12-24Vac/dc 2A max), and activation lasts according to the door opening time programmed. • In "capacitive discharge" operation...

NAME PLATE HOLDER AND LED MODULE INSTALLATION NAME PLATE HOLDER INSTALLATION (FIG. 5) ™\^VIDEX \ THE POWER TO SECURE 1. Insert the name plate holder®; 2. Insert the name plate support® ; 3. Insert the screws©. LED MODULE INSTALLATION (FIG. 6) 1. Remove the double-sided tape film ® placed on the back of the LED module © ; 2. By applying moderate pressure, make the LED module © adhere to the right inner of the box © (flush or surface mounting) in correspondence to the central part of the module. LED module electical features: 10/15vdc - 20mA. CONNECTION TERMINALS SIGNALS TECHNICAL SPECIFICATIONS...