Art. VR4KAM2W

Art. VR4KAM2W
1 / 12 PagesView full catalog

Art. VR4KAM2W

Product catalog summary
Overview: The document provides installation instructions for the Art.!VR4KAM2W, a digital front panel from the 4000 Series Vandal Resistant Range, designed for the VX2200 intercom system. It supports up to 24 functional push buttons and is available in multiple versions.
Description: The Art.!VR4KAM2W is a digital interface module that connects traditional buttons to the VX2200 system using a '2 wire' BUS. It includes a speaker unit and can be configured with 0, 1, 2, or 3 call buttons. The module is part of the vandal-resistant range and can be flush or surface mounted.
LED Indicators: The unit features three LEDs: Yellow (indicates conversation), Red (indicates busy state), and Green (indicates door open).
Controls: The module includes controls for balance, loudspeaker volume, and microphone volume, which can be adjusted to prevent feedback and optimize audio quality.
Programming: The unit can be programmed as a Master or Slave, with settings for button matrix address groups, conversation time, relay time, and unit ID. Programming is done via an 8-way dip-switch.
Operation: When a call button is pressed, the unit generates a coded address corresponding to the button. The system provides acoustic signals to indicate call status, such as busy, in progress, or door open.
Installation: Instructions are provided for installing the name plate holder and LED module, which are specific to certain versions of the unit.
Technical Specifications: The unit supports up to 23 users, operates at 13 Vdc, and has a power consumption of 30mA in standby and 200mA max. It functions within a temperature range of -10 to +50 °C.
Cleaning Instructions: Use a soft cloth with warm water or non-aggressive cleansers. Avoid abrasive, chlorine-based, or metal cleaning products.
Technical Specifications:
- Maximum Voltage: 24Vac/dc
- Relay Contact: Common and Normally Open (NO)
- Active Low Input: Enables door-opening relay
- Active Low Output: Active during call
- Busy Signal: Active low input/output
- Data Line: BUS input
- Ground Line: BUS input
- Power Supply: +12Vdc input
- Ground Input: Power supply
- Button Matrix: Columns (1..6), Rows (A..D)
- Memory Capacity: Up to 23 users
- Operating Voltage: 13 Vdc ±10%
- Current Consumption: Stand-by 30mA, Max 200mA
- Operating Temperature: -10 to +50 °C
Cleaning Instructions:
- Use a soft, clean cloth with warm water or a non-aggressive detergent.
- Do not use abrasive products, chlorine-containing products, or metal cleaners.
Disposal Instructions:
- Comply with Legislative Decree no. 49 of 14 March 2014 on WEEE.
- The crossed-out bin symbol indicates separate collection from mixed municipal waste.
- Dispose of at suitable waste collection centers or return to retailer when purchasing new equipment.
- Free disposal of very small WEEE (no external dimension over 25 cm) at retailers without purchase obligation.
- Proper disposal aids reuse, recycling, and recovery, preventing negative environmental and health effects.
Manufacturer Information:
- VIDEX ELECTRONICS S.P.A., Via del Lavoro, 1, 63846 Monte Giberto (FM) Italy
- Contact: Tel (+39) 0734 631669, Fax (+39) 0734 632475, www.videx.it, [email protected]
Customer Support:
- VIDEX ELECTRONICS S.P.A., www.videx.it, [email protected]
- UK Customers: VIDEX SECURITY LTD, www.videxuk.com, Tech Line: 0191 224 3174
Compliance:
- CE marked for conformity with EU Directives: 2014/30/EU (EMC), 2014/35/EU (LVD), 2011/65/EU (RoHS).
See more

Catalog excerpts

Art. VR4KAM2W-1

4000 Series Vandal Resistant Range vxVIDEX THE POWER TO SECURE © Loudspeaker volume ® Microphone volume © 8 way dip-switch © UIM138 connection @ Connection terminals DESCRIPTION The Art. VR4KAM2W unit is a digital front panel based on a "2 wire" BUS intercom system for the VX2200 system. This unit is housed in a single 4000 Series module from the VR4K vandal resistant range. It incorporates the functional interface connections from functional to digital and the speaker unit module with 0, 1, 2 or 3 call buttons. This device enables the connection of up to 24 functional push buttons using standard 4000 Series vandal resistant line extension module panels Art. VR4KBM-4, Art. VR4KBM-5, Art. VR4KBM-6, Art. VR4KBM-7, Art. VR4KBM-8 or Art. VR4KBM-9. The module built-in buttons, 1, 2 or 3 as factory presetting are set as 1st ID PHONE or 1st and 2nd or 1st, 2nd and 3rd of the addresses group ("1..24" or "25..48") programmed. All the modules must be assembled using the 4000 Series flush or surface mounting units. LEGEND ® Loudspeaker ® Yellow LED © Red LED © Green LED © Call button © Balance AVAILABLE VERSIONS

 Open the catalog to page 1
Art. VR4KAM2W-2

™\^VIDEX \ THE POWER TO SECURE 4000 Series Vandal Resistant Range Art. VR4KAM2W Digital to functional interface module PROGRAMMING The programming enables the unit to be programmed as a MASTER or SLAVE (When more units are connected to the same bus only one must be master while the others must be slave), the button matrix address group to be programmed (1-24, 2548, 49-72 or 73-96), the "CONVERSATION TIME" (1 or 2 minutes), the "RELAY TIME" (1 or 6 seconds), the UNIT ID (1..8 Each door should have a unique ID) that is used for selective camera recall and to show on the concierge (if installed...

 Open the catalog to page 2
Art. VR4KAM2W-3

™\^VIDEX \ THE POWER TO SECURE 4000 Series Vandal Resistant Range Art. VR4KAM2W Digital to functional interface module PROGRAMMING NOTES In case of a wrong Master/Slave configuration, the following problems can occur: a. if the unit should be a Master but is configured as a Slave, the error is signalled by an acoustic intermittent signal until the problem is resolved; b. if the unit must be Slave but is configured as Master, the impedance of the system will have a lack of balance, causing feedback ("Larsen" effect). When a system uses a concierge unit Art. VX2210-1 the push button combined to...

 Open the catalog to page 3
Art. VR4KAM2W-4

vxVIDEX THE POWER TO SECURE Serie 4000 Linea Antivandalo © Volume altoparlatne © Volume microfono ® Dip-switch a 8 vie © Connessione UIM138 © Morsetteria di connessione DESCRIZIONE L'Art. VR4KAM2W e un'unita di chiamata digitale su BUS "2 fili" che permette la connessione di pulsanti tradizionali al sistema digitale VX2200. L'unita e alloggiata in un modulo Serie 4000 linea anti-vandalo e la sua elettronica si compone dell'interfaccia analogico-digitale e del portiere elettrico con 0, 1, 2 o 3 pulsanti in base al modello. L'interfaccia permette il collegamento di 24 pulsanti tradizionali impiegando...

 Open the catalog to page 4
Art. VR4KAM2W-5

vxVIDEX THE POWER TO SECURE Serie 4000 Linea Antivandalo Art. VR4KAM2W Unita di chiamata digitale PROGRAMMAZIONE La programmazione permette di impostare I'unita come MASTER o SLAVE (per tutte le unita sullo stesso livello pud essere presente un solo master), di configurare il gruppo di indirizzi generato dalla matrice dei pulsanti (1-24, 25-48, 49-72 o 73-96), il "TEMPO DI CONVERSAZIONE" (1 o 2 minuti) che determina la durata massima della conversazione, il "TEMPO RELE" (1o 6 secondi) che stabilisce la durata dell'attivazione del rele e l'lD DI UNITA' (1..8) che e necessario per l'auto-accensione...

 Open the catalog to page 5
Art. VR4KAM2W-6

NOTE DI PROGRAMMAZIONE Nel caso di una errata configurazione Master/Slave, si possono verificare i seguenti inconvenienti: a. se l'unita deve essere Master, ma viene configurata come Slave, viene segnalato l'errore con un segnale acustico intermittente fino alla risoluzione del problema; b. se l'unita deve essere Slave, ma viene configurata come Master, si avra uno squilibrio dell'impedenza dell'impianto che si potreb-be manifestare attraverso dei rumori (effetto "Larsen"); i rumori spariranno alla risoluzione del problema. Se nel sistema e presente il centralino digitale, il pulsante al quale...

 Open the catalog to page 6
Art. VR4KAM2W-9

VX2200 Video door entv system using vandal resistant modules Sistema videodtofonico VX2200 con moduli della linea anti-vandalo Roberto Gambini

 Open the catalog to page 9
Art. VR4KAM2W-11

In accordance with the Legislative Decree no. 49 of 14 March 2014 “Implementation of the Directive 2012/19/EU on waste electrical and electronic equipment (WEEE)”. The crossed-out bin symbol on the equipment or on the packaging indicates that when the product reaches the end of its lifetime, it must be collected separately from mixed municipal waste. The user must, therefore, dispose of the equipment at the end of its lifetime in the suitable waste collection centres or bring it to the retailer during the purchase of a new equipment of equivalent type at the ratio of one-to-one. Furthermore,...

 Open the catalog to page 11
Art. VR4KAM2W-12

Main UK office: VIDEX SECURITY LTD 1 Osprey Trinity Park Trinity Way LONDON E4 8TD Phone: (+44) 0370 300 1240 Fax: (+44) 020 8523 5825 www.videxuk.com [email protected] Northern UK office: VIDEX SECURITY LTD Unit 4-7 Chillingham Industrial Estate Chapman Street NEWCASTLE UPON TYNE - NE6 2XX Tech Line: (+44) 0191 224 3174 Phone: (+44) 0370 300 1240 Fax: (+44) 0191 224 1559 Greece office: VIDEX HELLAS Electronics 48 Filolaou Str. 11633 ATHENS Phone: (+30)2107521028 (+30) 2107521998 Fax: (+30) 210 7560712 www.videx.gr [email protected] Dutch office: NESTOR COMPANY BV Business Center Twente (BCT)...

 Open the catalog to page 12
*Prices are pre-tax. They exclude delivery charges and customs duties and do not include additional charges for installation or activation options. Prices are indicative only and may vary by country, with changes to the cost of raw materials and exchange rates.