- Catalogs
- Ventilclima
- Controller
Controller
Controller
This section provides a detailed table for selecting controllers, including various types of control panels and thermostats. It covers options for base control panels, sheet base control panels, and electronic thermostats, specifying applications such as 2-pipe and 4-pipe systems. Key features highlighted include remote control, temperature regulation, and fan speed settings.
The document describes different product types, such as fan coil controllers without room temperature control and electromechanical control panels with bulb thermostats. These are suitable for hotel rooms, offices, and homes requiring manual functions. Compatibility with 2-pipe and 4-pipe systems, with or without valves, is specified.
Operational instructions are provided for configurations like 2-pipe fan coils with and without valves, and 4-pipe fan coils with two valves. Manual switches control fan operation and valve opening in heating and cooling modes, with fan operation specifications based on water temperature.
Guidelines indicate that control panels can be mounted directly on the fan coil, with a power supply requirement of 230 Vac 50 Hz.
Special functions include economy mode, fan-only operation, and master/slave configurations. Accessories such as minimum water temperature thermostats and room temperature remote bulb thermostats are listed with purchase codes.
For heating, if a minimum water temperature thermostat is installed, the fan starts when the exchanger temperature exceeds 35°C. In cooling mode, the fan runs at the set speed. Accessories like thermostats, air intake sensors, and wall boxes are listed with purchase codes.
Electronic thermostats for fan coils are described, suitable for 2-pipe and 4-pipe systems. Functions include switching the fan coil on/off, room temperature adjustment, and manual or automatic heating/cooling selection. Installation options include wall-mounted or directly on the fan coil.
Thermostat operation varies based on configuration. For 2-pipe systems without valves, the fan starts when needed and stops when the desired temperature is reached. For systems with valves, the thermostat controls valve operation. In 4-pipe systems, heating or cooling is set manually, with thermostat control over valves.
Programmable thermostats with LCD displays offer features like manual or automatic speed selection, temperature display, and on/off valve control. Power options include 230 Vac or 24 Vac, depending on valve requirements.
- Manual and automatic speed selection with a 0-10Vdc modulating signal.
- Display for environment temperature and set point.
- On/off valve control and EC fan driver (0-10Vdc).
- Programmable functions.
- Wall-mounted or onboard the fan coil.
- Power supply options: 230 Vac 50Hz for 230V AC valves, 24 Vac 50 Hz for 24V AC valves.
- Control of a single fan coil in hotel rooms, offices, and homes requiring automated functions and precise fan modulation.
- Suitable for 2-pipe systems, 2-pipe systems with valve, and 4-pipe systems with automatic heating/cooling switching.
- Thermostat parameters allow defining the operating mode based on installation or system requirements.
- Programming is done via buttons and knob as per manual instructions.
- Defines system type, control mode, manual or automatic heating/cooling switching, and various operational values.
- Air intake sensor (NTC) and water sensor for winter minimum function or automatic heating/cooling changeover.
- Transformer 230/24 Vac for use with 24 Vac valves.
- Wall box for air sensor and extra price for special cable lengths.
- Programmable electronic thermostat with LCD for 2 or 4 pipe fan coils.
- Main functions include switching the fan coil on/off, room temperature adjustment, manual/automatic heating/cooling selection, and control of modulating valves and motor.
- Installation options include wall-mounted or directly on the fan coil.
The document outlines specifications for a thermostat and fan coil system, including parameters like minimum water temperature, economy mode, neutral zone amplitude, hysteresis, proportional bands, fan stop delays, and filter control warning time. It emphasizes the importance of using valves for proper operation when installed directly on the fan coil.
The thermostat can be programmed to suit installation or system requirements, allowing for the definition of system type (2 or 4 pipes, with or without external sensors), control mode (valves, fan, both), valve type (on-off or floating/3-point), and manual or automatic changeover between cooling and heating. The thermostat is connected to the RCVF1 controller via two signal wires, enabling easy placement within the environment.
The RCVF1 is an electronic device designed for linear speed regulation of fan coils, allowing for continuous speed control via a 0-10V or PWM signal. It provides acoustic comfort by avoiding abrupt speed changes. The power supply is 230 Vac, with inputs for PWM and 0-10V signals.
The system is suitable for controlling single fan coils in hotel rooms, offices, and homes, offering precision and modern design. It supports 2-pipe and 4-pipe systems with automatic or manual heating/cooling changeover.
The thermostat allows for the definition of operational parameters such as room temperature differential, automatic speed change temperature level, neutral zone amplitude, and control mode. It supports both manual and automatic heating/cooling changeover and includes inputs for minimum water temperature sensors.
No accessories are provided with the RCVF1 controller.
1. NTC 10 kΩ Sensor: Used for air intake temperature with a 1.5 m cable. Available in mounted (A0055150204) and loose (A0055150085) versions.
2. PTC 2 kΩ Sensor: Designed for water temperature with a 0.7 m cable. Available in mounted (A0055150206) and loose (A0055150090) versions.
3. GEWISS Black External Cover: Available loose and not mounted (A0055150114).
The document describes a weekly electronic chronothermostat with an LCD display, suitable for controlling heating and cooling systems in offices and homes. It features weekly programming, environment temperature control, and manual heating/cooling selection. The device is wall-mounted and powered by 230 Vac/50Hz.
The chronothermostat is ideal for automating the switch on/off of heating/cooling systems for comfort and energy savings. It is suitable for controlling single or multiple fan coils, zone valves, and circulation pumps.
The device can operate manually or automatically based on time and environment temperature. It controls fan coils, zone valves, and circulation pumps by switching them on or off according to the preset environment temperature. Note that it cannot control the three fan speeds and requires interfacing with a relay for output.
An interface card is available for controlling up to four fan coils from a single thermostat. It includes inputs and outputs for fan speed and valve control, suitable for 2 or 4-pipe systems.
The document lists various control panels and accessories, including electronic thermostats and remote controls, suitable for different fan coil models. No additional accessories are provided for some products.
Control systems for cassette fan coils include features like temperature adjustment, mode selection, fan speed control, and a daily timer. The fan operation is specified based on water temperature for both heating and cooling modes.
Control of a single zone valve or circulating pump, suitable for a 2-pipe system. The thermostat manages the opening and closing of the zone valve or circulating pump based on temperature requirements.
The thermostat opens the zone valve or starts the circulating pump when heating or cooling is needed and stops them once the desired room temperature is reached.
Includes air intake sensors with specific codes for mounted and loose configurations. Additional costs apply for non-standard cable lengths.
- Slide Selector Switch: For fan coil units, allows manual 3-speed settings and is wall-mounted. Available in white and black.
- Rotary Selector Switch: Similar to the slide selector but uses a rotary mechanism, suitable for B-TICINO mounting boxes.
- Continuous Speed Controller: For heat recovery units, offers continuous fan speed control and additional functionalities like reheat control. Available in models with different amperage ratings.
- Antifreeze Thermostat: Protects batteries and checks external air temperature, ensuring temperatures do not fall below 5°C.
- Wall Humidistat: Monitors and controls relative humidity for fan coil units, activating in cooling mode.
- Continuous Fan Speed Controller: Provides linear speed control for single-phase motors, offering energy savings and acoustic comfort.
Each device operates by adjusting settings such as speed or temperature through knobs or switches, with specific configurations for installation and power supply.
Each product is designed for specific applications, such as controlling a single fan or heat recovery unit. Some products are not suitable for fan coils, and specific installation requirements must be met to ensure compliance with safety and electromagnetic compatibility standards.
This document describes a supervision system for fan coils, detailing its components, functionalities, and applications. The system is designed for environments requiring high automation of comfort and energy savings, such as hotels, offices, homes, and hospitals.
- Onboard Controller: An electronic card installed on the fan coil, controllable via a PC, zone router, or wall-mounted control.
- Wall-Mounted Local Controller: Allows local control of the fan coil.
- Remote Control: Enables control of the wall-mounted controller and can be paired with a receiver on the fan coil.
- Electronic Card for Auxiliary Devices: Manages circulation pumps, gates, boilers, and chillers with 8 relay outputs controlled by a PC.
- Floor Router: Required for installations with more than 60 fan coils, facilitating communication between fan coils and the PC.
- Supervision Software: Manages the system from a PC, including an RS232-485 interface and power supply.
- Temperature control of environments/zones.
- Control of auxiliary devices.
- Manual and automatic 3-speed selection.
- Manual or automatic heating/cooling selection.
- Calendar and hourly operation ranges.
- Temperature set point threshold.
- Alarm status monitoring.
The system is suitable for 2-pipe and 4-pipe systems with automatic heating/cooling switching. It is ideal for environments requiring maximum comfort and energy efficiency.
The system allows monitoring and parameter adjustments from a PC without needing to operate specific controls. It supports defining system types, control modes, and temperature regulation values.
- Air sensor with potentiometer.
- Air/water sensor.
- Plastic cover for supervision card.
The supervision system supports 2 or 4 tube fan coils, featuring onboard controllers for various valve types, multiple inputs for temperature and fault sensors, and options for automatic season changeover. The wall-mounted control includes buttons for temperature, fan speed, and mode selection. The floor router and supervision software provide additional functionalities like temperature control limitation, time programming, energy cost estimation, and event history tracking.
Catalog excerpts
CONTROL Regolazione Controller
Open the catalog to page 1
Regolazione Controller Termostato elettronico Electronic thermostat Termostato elettronico Electronic thermostat Termostato elettronico programmabile Programmable electronic thermostat Termostato elettronico programmabile Programmable electronic thermostat Termostato elettronico programmabile Programmable electronic thermostat Termostato elettronico Electronic thermostat CD12 Comando senza regolazione di temp. Control without temperature control CD11 Termostato elettronico Electronic thermostat Telecomando + scheda + ricevitore Remote control + motherboard + receiver TRI/F1 Commutatore Changeover...
Open the catalog to page 2
Regolazione Controller Sistema di supervisione Xxxxxxxxxx Reg. a sintesi di frequenza con ingresso 0-10Vdc (10A) Antifreeze Reg. a sintesi di frequenza con ingresso 0-10Vdc (2A) Antifreeze Reg. a sintesi di frequenza con potenziomentro (10A) Antifreeze Termostato elettronico Electronic thermostat TA/1 Reg. a sintesi di frequenza con potenziomentro (2A) Antifreeze Accessorio per ventilconvettore a cassetta Accessory for cassette unit CD4S Umidostato da parete Wall humidistat Scheda di interfaccia Interface card SDI-V Termostato antigelo Antifreeze Regolatore continuo di velocità Speed continuos...
Open the catalog to page 3
Regolazione Controller QUADRO COMANDO BASE BASE CONTROL PANEL COD. MONTATO - MOUNTED Senza cornice Without horse-shoe plate With horse-shoe plate SFUSO - LOOSE Senza cornice Without horse-shoe plate With horse-shoe plate With left and right horse-shoe plate PRODUCT TYPE Comando per ventilconvettore senza regolazione di temperatura ambiente per ventilconvettore a 2 o 4 tubi. Funzioni principali: - accensione e spegnimento del ventilconvettore; - selezione riscaldamento/raffrescamento manuale; - selezione 3 velocità manuale; - Installazione: - a bordo del ventilconvettore; - Alimentazione: - 230...
Open the catalog to page 4
Regolazione Controller QUADRO COMANDO BASE IN LAMIERA (xx0) SHEET BASE CONTROL PANEL (xx0) COD. MONTATO - MOUNTED SFUSO - LOOSE PRODUCT TYPE Comando per ventilconvettore senza regolazione di temperatura ambiente Funzioni principali: - accensione e spegnimento del ventilconvettore; - selezione riscaldamento/raffrescamento manuale; - selezione 3 velocità manuale; - Installazione: - a bordo del ventilconvettore; - Alimentazione: - 230 Vca 50 Hz Fan coil controller without environment temperature control Main functions: - fan coil switching on/off; - manual heating/cooling selection; - manual 3 speed...
Open the catalog to page 5
Regolazione Controller COMANDO ELETTROMECCANICO IN LAMIERA (xx6) SHEET ELECTROMECHANICAL CONTROL PANEL (xx6) COD. MONTATO - MOUNTED SFUSO - LOOSE PRODUCT TYPE Quadro comando elettromeccanico con termostato ambiente a bulbo per ventilconvettori. Funzioni principali: Accensione e spegnimento del ventilconvettore Regolazione temperatura ambiente Selezione riscaldamento/raffrescamento manuale Selezione 3 velocità manuale Installazione: - a bordo del ventilconvettore Alimentazione 230 Vca 50Hz Electromechanic control panel with environment bulb thermostat for fan coils. Main functions: Fan coil switching...
Open the catalog to page 6
Regolazione Controller TERMOSTATO AMBIENTE A BULBO (PER QUADRO COMANDO BASE) BULB ROOM THERMOSTAT (FOR BASE CONTROL PANEL) COD. MONTATO - MOUNTED SFUSO - LOOSE PRODUCT TYPE Termostato ambiente a bulbo per ventilconvettore a 2 o 4 tubi; Funzioni principali: - accensione e spegnimento del ventilconvettore; - regolazione temperatura ambiente; - selezione riscaldamento/raffrescamento manuale; - selezione 3 velocità manuale; - Installazione: - a bordo del ventilconvettore; - Alimentazione: - 230 Vca 50 Hz - Ingresso per termostato di minima temperatura acqua (contatto bimetallico); - 2 uscite per...
Open the catalog to page 7
Regolazione Controller QUADRO COMANDO CON TERMOSTATO AMBIENTE ELETTRONICO CONTROL PANEL WITH ELECTRONIC ROOM THERMOSTAT COD. MONTATO - MOUNTED Senza cornice Without horse-shoe plate A005515SX15 A005515DX15 With horse-shoe plate SFUSO - LOOSE Senza cornice Without horse-shoe plate With horse-shoe plate PRODUCT TYPE Termostato elettronico per ventilconvettore; Funzioni principali: - accensione e spegnimento del ventilconvettore; - regolazione temperatura ambiente; - selezione riscaldamento/raffrescamento manuale; - selezione 3 velocità manuale; - Installazione: - a bordo del ventilconvettore; -...
Open the catalog to page 8
Regolazione Controller TERMOSTATO DI CONSENSO WATER LOW TEMPERATURE THERMOSTAT MONTATO - MOUNTED SFUSO - LOOSE PRODUCT TYPE Termostato di consenso (minima temperatura acqua) per: - quadro comando base; - quadro comando base + termostato ambiente a bulbo; - quadro comando con termostato ambiente elettronico; - CD11; - CD12. Installazione: - a bordo del ventilconvettore (predisposto per l’inserzione fra le alette dello scambiatore). Low temperature thermostat (minimum water temperature) for: - basic control panel; - basic control panel + room temperature remote bulb thermostat; - control panel...
Open the catalog to page 9
CONTROL VEMA Regolazione Controller TERMOSTATO DI CONSENSO A BRACCIALE WATER LOW TEMPERATURE STRAP FASTENING THERMOSTAT SFUSO - LOOSE PRODUCT TYPE Termostato di consenso (minima temperatura acqua) Installazione: - a bordo del ventilconvettore (predisposto per il fissagio a tubo con apposito collarino a molla). Low temperature thermostat (minimum water temperature) Installation: - directly on the fan coil (designed for fixed on pipe with special spring collar) DESCRIZIONE PRODOTTO PRODUCT DESCRIPTION Termostato a contatto per utilizzo in modalità riscaldamento. Contatto bimetallico normalmente aperto....
Open the catalog to page 10
Regolazione Controller PRODUCT TYPE Commutatore per cambio automatico fra riscaldamento/raffrescamento da utilizzare con quadro comando base con termostato ambiente a bulbo o elettronico e con termostato CD12C. Installazione: - a bordo del ventilconvettore (predisposto per il fissaggio a tubo con apposito collarino in acciaio) Automatic heating/cooling changeover switch to be used with basic control panel with electronic or room temperature remote bulb thermostat and with thermostat CD12C.. - Installation: - directly on the fan coil (designed for fixing to pipe with relative steel clip) DESCRIZIONE...
Open the catalog to page 11All Ventilclima catalogs and technical brochures
GALILEO PRODUCT SHEET24 Pages
VTE Tangential fan coil unit8 Pages
VCE Centrifugal fan coil unit12 Pages
Centrifugal fan coil unit16 Pages
LIGHT12 Pages
