Valspar® Storm Coat™ Exterior Flat Paint
2Pages

Valspar® Storm Coat™ Exterior Flat Paint No. 145390 Series GENERAL DESCRIPTION PRODUCT SPECIFICATIONS Stir paint thoroughly. Intermix containers to ensure uniform color. Apply with a premiumquality roller, polyester brush or airless sprayer. Paint the ceiling first, then the walls. If applying by roller, roll from dry area into wet area using firm, crisscross strokes. Finish with long, even strokes in one direction. Note: Some deep or bright colors may require an additional coat to obtain complete hide. Surface conditions and application technique can also impact coverage. Vehicle Type: Acrylic Pigment Type: Titanium Dioxide Viscosity: 92–100 Krebs Units Sheen: 0–5 Units @ 60° angle VOC (g/L): Less than 50 g/L Volume Solids: 31% Weight Solids: 46% Weight Per Gallon: 10.9 lbs./gal. Practical Coverage: Covers up to 350–450 sq. ft. per gallon (32–42 m2 per 3.78 L). Less on rough or porous surfaces. Recommended Film Thickness: 4.0 mil Wet 1.2 mil Dry Dry Time @ 77 °F and 50% Relative Humidity To The Touch: 1 hour Recoat: 4 hours Dry Time @ 35–45 °F and 50% Relative Humidity To The Touch: 2 hours Recoat: 24 hours Application Temperature: 35–90 °F (2–32 °C) Storm Flat is a 100% Acrylic, Professional Quality, Exterior Latex Paint developed to provide outstanding durability, fade resistance and mildew resistance. It can be applied at temperatures as low as 35 OF allowing you to extend the painting season. Storm Coat Flat provides a smooth, uniform finish with spray, brush or roller application and can be applied to a variety of exterior surfaces: Wood and metal siding, trim including hardboard, fiber cement board, vinyl, shakes, primed metal, brick, cement, and cured cinder block and stucco. 100% Acrylic resin provides maximum durability and color retention Applies at temperatures as low as 35 OF Excellent hide & coverage Film provides mildew resistance Great touch-up and flow & levelling provide a smooth, uniform finish Application with spray, brush and roller RECOMMENDED USES Properly prepared exterior wood and metal siding and trim including hardboard, fiber cement board, vinyl, primed metal, shakes, brick, cement, cinder block and stucco. Do not use on glazed brick, floors or steps. SHIPPING AND PACKAGING Freight Classification: Paint or paint related material. Protect from freezing. Packaging: Gallon – 4 per carton 5 gallon pail COMPOSITION Base and Fill Levels (oz./gal.) 128 Airless Spray: Pressure: 2000 PSI Tip: 0.017–0.019” Brush: premium-quality nylon or polyester brush Roller: premium quality synthetic, 3/8” nap SYSTEM RECOMMENDATIONS Wood: 1 Coat: Valspar All-Weather Exterior Latex Primer Sealer 1-2 Coats: Storm Coat Exterior Flat Paint Hardboard Siding: 1 Coat: Valspar All-Weather Exterior Latex Primer Sealer 1-2 Coats: Storm Coat Exterior Flat Paint Masonry and Stucco: 1 Coat: Valspar Masonry and Stucco Primer 1-2 Coats: Storm Coat Exterior Flat Paint Concrete Block: 1 Coat: Valspar Block Filler 1-2 Coats: Storm Coat Exterior Flat Paint Galvanized Metal and Aluminum: 1 Coat: Valspar Galvanized Metal Primer 1-2 Coats: Storm Coat Exterior Flat Paint Ferrous Metal: 1 Coat: Valspar Professional DTM Acrylic Primer 1-2 Coats: Storm Coat Exterior Flat Paint Vinyl Siding: 2 Coats: Storm Coat Exterior Flat Paint REGULATORY COMPLIANCE Current as of: 2/23/2015 SCAQMD CARB 2000 SCM CARB 2007 SCM OTC/LADCO US National LEED (US) LEED (Canada) CLEANUP AND DISPOSAL Clean up with warm, soapy water. Do not freeze. Keep container closed when not in use. Do not transfer contents to other containers for storage or disposal. In case of spills, absorb with inert material such as sand or kitty litter. Dispose of empty container or unused portion in accordance with local, state and federal regulations. The data on this sheet represent typical values. Since application variables are a major factor in product performance, this information should serve only as a general guide. Valspar assumes no obligation or liability for use of this information. UNLESS VALSPAR AGREES OTHERWISE IN WRITING, VALSPAR MAKES NO WARRANTIES, EXPRESS OR IMPLIED, AND DISCLAIMS ALL IMPLIED WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE OR FREEDOM FROM PATENT INFRINGEMENT. VALSPAR WILL NOT BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES. Your only remedy for any defect in this product is the replacement of the defective product, or a re

Valspar® Storm Coat™ Exterior Flat Paint No. 145390 Series SURFACE PREPARATION SURFACE PREPARATION Block, Concrete, and Masonry: Read the Lead Warning paragraph. Thoroughly clean the surface and allow to dry. Remove all wax, grease, dirt, chalk, mildew, loose and peeling paint, and other foreign matter. Remove gloss from shiny surfaces. Fill all cracks and joints with Acrylic caulk before top coating. Remove any powdery dust and efflorescence. New or bare surfaces should be primed with an appropriate Valspar® primer. Masonry surfaces and mortar should be fully cured, usually 30 days. Remove...