Technical Sheet www.valpaint.it * www.valpaintjungle.it Via dell'Industria, 80 ■ 60020 POLVERIGI (AN) ITALY E-mail: [email protected] TECHNICAL DATA DRYING TIME: textured coating water based decoration paint for indoor use specific weight: aesthetic effect: 4 - 5 m2/LT (it may vary according to the roughness, porosity and surface absorption and to the method of application ) colours from the catalogue Stainless steel trowel and spatula APPLICATION CYCLE: Spatula-Stroke Effect: Apply a coat of METEORE 8 gradually over a surface of approx. 1 - 2 m2. Use the PV 43 Trowel and apply 10 - 15 cm long irregular strokes in all directions. While METEORE 8 is still wet, create semi-smooth relief and striped spatula strokes using the PV 43 Trowel, with 5 - 10 cm long strokes in all directions. After about 4 hours at 20°C smoothen with 220 / 260-grit sandpaper to remove any irregular clots and joints. Subsequently apply two different-coloured coats of LAME'. Between the first and second coat of LAME', wait at least 2 hours at 20°C. LAME' must also be applied with the PV 43 Trowel in all directions, leaving very little product on the surface. Coverage: METEORE 8 roughly 1 litre for 4 - 5 m2; LAME' roughly 1 litre for 16 - 20 m2 (one colour coat depending on the thickness of METEORE 8 applied). Veined Effect (Vertical, Horizontal, Oblique: Apply a coat of METEORE 8 gradually over a surface of approx. 2 - 3 m2. Use the PV 43 Stainless Steel Trowel and apply irregular strokes in the chosen direction. While METEORE 8 is still wet, create vertical streaks (or in another direction as desired) using the PV 84 Spatula and apply 20 - 35 cm long, soft stokes. After about 4 hours at 20°C smoothen with 220 / 260- grit sandpaper to remove clots and any irregular joints. Subsequently apply two different-coloured coats of LAME'. Between the first and second coat of LAME', wait at least 2 hours at 20°C. LAME' must also be applied with the PV 43 Trowel in the direction of the streaks, leaving very little product on the surface. Coverage: METEORE 8 roughly 1 litre for 4 - 5 m2; LAME' roughly 1 litre for 16 - 20 m2 (one colour coat depending on the thickness of METEORE 8 applied). Floral Effect: Apply a coat of METEORE 8 gradually over a surface of approx. 1 - 2 m2. Use the PV 43 Trowel and apply 20 - 30 cm long irregular strokes in all directions. While METEORE 8 is still wet, apply continuous narrow and round strokes using the PV 84 Spatula. After about 4 hours at 20°C smoothen with 220 / 260-grit sandpaper to remove any irregular clots and joints. Subsequently apply two different-coloured coats of LAME'. Between the first and second coat of LAME', wait at least 2 hours at 20°C. LAME' must also be applied with the PV 43 Trowel in all directions, leaving very little product on the surface Coverage: METEORE 8 roughly 1 litre for 4 - 5 m2; LAME' roughly 1 litre for 16 - 20 m2 (one colour coat depending on the thickness of METEORE 8 applied). E-mail: [email protected] E-mail: [email protected] VALPAINT TUNISIES.A. Zone Industrielle Zaghouan E-mail: [email protected]

www.valpaint.it * www.valpaintjungle.it Via dell'Industria, 80 ■ 60020 POLVERIGI (AN) ITALY E-mail: [email protected] Smooth Effect: Apply one coat of METEORE 8 using the PV 43 Trowel with 15 - 20 cm long strokes in all directions. Wait for METEORE 8 to tighten up then smoothen it slightly using the clean Trowel with strokes in all directions. After 4 hours at roughly 20°C, smoothen the surface using 220 / 260-grit sandpaper to remove any irregular clots and joints then apply two different-coloured coats of LAME'. Between the first and second coat of LAME', wait at least 2 hours at 20°C. LAME'...