ANTICANDO 300
2Pages

Via dell'lndustria, 80 - 60020 POLVERIGI (AN) ITALY E-mail: info@valpaint.it Tecnical Sheet DRYING TIME: thick coating water-based product which yields special antique effects. Decoration of indoor plaster after the standard masonry wall preparations. specific weight: aesthetic effect: roughness, porosity and surface absorption and to the colours shown in the catalogue achievable using below the surface: 24 hours at 20°C ANTICANDO 300 is made using acrylic resins and natural fillers. After application, the decorated surface remains breathable, washable and may be painted over. ANTICANDO 300 is easily applied to various types of surface, such as cement, plaster, plaster of Paris, plasterboard, wood and iron after suitable treatment has been applied. Old walls. Remove old non-adhering and peeling paint from the support and wash using water and a suitable soap product. Next, apply a coat of PRIMERT 400 diluted 50% with water to act as a fixative. After approximately 4 hours at 20°C, apply a second brushed coat of PRIMER 400 diluted 20 - 30% with water. If, however, the surfaces are clean and not peeling, apply a coat of PRIMER 400 diluted 20 - 30% with water. After 4 hours at 20°C, proceed with the application of ANTICANDO 300 dilution: ANTICANDO 300 is ready to use ( it can be diluted with water to get the other decorative system: brush or spatula APPLICATION CYCLE: ANTICANDO 300 is ready to use and should be mixed well. The special PV 77 plastic spatula or the plastic trowel PV 90 or PV 91 or a stainless steel trowel should be used to apply the product directly to both new and old sound surfaces which are free from dust, even if they have already been painted. An uneven layer should be spread over the entire surface, leaving visible irregular and raised strokes which are close together. After 8 hours at 20°C, when ANTICANDO 300 has dried properly, proceed with the application of non-coloured FINIX 60. After approximately 6-8 hours at 20°C, apply a second coat of coloured FINIX 60. On both coatings use a small quantity of products with VALPAINT TUNISIESA. 2° Stabilimento VALPAINT MAROC S.A.R.L VALPAINT ALGERIE S.A.R. ZonelnduslridbZaghouan Rue Des Entrepreneurs, 43 Rue Kaied El Achlar, 7 Route de Setif, 9 L. VALPAINT ESPANA S.L VALPAIN1 DESIGN D.O.O. Altro PuntoVendita: Atro Punto Vendita: Calle Magdalenes, 25 3° Diemala Bijedica, 281 V Proleterske Brigade, 255 1C Solidum-Skorpikova, 11 08002 BARCELONA-ESPANA 71000 SARAJEVO - BiH 81000PODGORICA- MONTENEGRO 10090 ZAGREB - CROATIA E-mail: info@valpaint.es E-mail: valpaint@bih.net.ba E-mail: info@walpaint-desgn.com E-mail: info@ralpaint-desyn.hr

Via dell'lndustria, 80 - 60020 POLVERIGI (AN) ITALY E-mail: info@valpaint.it irregular brush strokes in all directions. Next, while the FINIX 60 is still wet and using the PV 77 spatula, work the product with criss-crossed spatula strokes, exerting a strong pressure, on the surface. N.B: ANTICANDO 300 becomes washable with water and common detergents after 15 days from application. Storage: make sure the tin is tightly closed, even after use, at a temperature no lower than +5°C and no higher than +30°C. Stability: approximately 2 years in well closed never opened tin WARNING: ANTICANDO 300...