Multi-compartment
10Pages

Total Cable Management Solutions MULTI-COMPARTMENT TRUNKING SYSTEMS With Multi-Compartment Trunking, dividing fillets are normally supplied spot-welded in position, but can also be supplied loose for fixing on site by drilling and screwing. Spot welds can be treated with Norgalv paint as an extra on request. Purpose-made trunking can be supplied with conduit entries at pre-determined regular intervals in sides and in dividing fillets. When trunking is mounted vertically or in the inverted position it is recommended that Cable Supports should be fitted. Bends, Tees, Intersections, etc, can be supplied complete with Dividing Fillets In Tees with Top Lids and in Intersection Boxes, Cross-over Bridges are fitted. Several example assemblies in Tees and Bends with unequal compartments are shown in this section. Three, four or more compartment trunking is available. ACCREDITED TO THE FOLLOWING STANDARDS

Standard Trunking Multi Compartment Trunking MULTI-COMPARTMENT TRUNKING SYSTEMS PLEASE NOTE: This section is to be used as an aid when ordering unequally divided and TOP LID and therefore directional Trunking Fittings. For INSIDE or OUTSIDE LID fittings all we need to know is the size of each compartment, therefore the steps below are only applicable for TOP LID Accessories. Trunking Direction Using the four-way diagram shown, decide what scenario best suits your situation. This will enable you to give information about the trunking sizes you are working with and the size of each trunking...

MULTI-COMPARTMENT TRUNKING SYSTEMS Size of Trunking (Trunking Direction Example) Tell us what size of trunking you are using. Select the appropriate fitting you require from the ‘Fitting Key’ shown at the bottom of this page. Each fitting has a unique number which should then be D1 used to fill in the order table. Fitting Key CHOOSE FITTING NUMBER BELOW: TEE: 36 Product Finishing Key (See page 24)

Standard Trunking Multi Compartment Trunking MULTI-COMPARTMENT TRUNKING SYSTEMS Compartment Size & Cable Run Lighting Trunking State the compartment sizes and where the cabling will run from/to by filling in Table 2. Speedway Cable Ladder Table 2 Trunking Compartment sizes & Cable runs (Example) (State Measurements in mm) Cable Basket Systems Cable Tray The remaining spaces should be left blank. For example, in this instance: Cable runs: Compartment Channel & Support Floor Trunking Bench Outlet & Perimeter Trunking Steel Conduit (Class 4) Innovative Design Solutions Accessories & Supports...

MULTI-COMPARTMENT TRUNKING SYSTEMS Trunking Size 100 x 50 x 3 Compartments (code: TK42x3) 90° or 45° Top Lid Bend with smaller compartments to the inside. Trunking Direction Compartment Size & Cable Run To... (mm) 38 Product Finishing Key (See page 24)

Standard Trunking Multi Compartment Trunking MULTI-COMPARTMENT TRUNKING SYSTEMS Speedway Cable Ladder 90° or 45° Top Lid Bend with smaller compartments to the outside. Cable Tray Lighting Trunking Trunking Size 150 x 50 x 2 Compartments (code: TK62x2) Floor Trunking Channel & Support Cable Basket Systems Bench Outlet & Perimeter Trunking Compartment Size & Cable Run To... Steel Conduit (Class 4) Trunking Direction Accessories & Supports Innovative Design Solutions visit online: uk unitrunk.co.uk ireland unitrunk.ie

MULTI-COMPARTMENT TRUNKING SYSTEMS Trunking Size 150 x 50 x2 Compartments (code: TK62x2) Top Lid TEE with underpass taking cables from the right hand compartment out from the rear compartment. Trunking Direction Compartment Size & Cable Run 40 Product Finishing Key (See page 24)

Standard Trunking Multi Compartment Trunking MULTI-COMPARTMENT TRUNKING SYSTEMS Speedway Cable Ladder Top lid Tee with 2 No crossover pieces to allow cables to Tee off in the correct order to suit the branched trunking supply. Cable Tray Lighting Trunking Trunking Size 200 x 100 x 3 Compartments (code: TK84x3) Floor Trunking Cable Basket Systems Channel & Support Bench Outlet & Perimeter Trunking Trunking Direction Compartment Size & Cable Run Innovative Design Solutions Accessories & Supports Steel Conduit (Class 4) visit online: uk unitrunk.co.uk ireland unitrunk.ie

MULTI-COMPARTMENT TRUNKING SYSTEMS ORDER SHEET Using steps 1 to 4 as outlined in this section, please complete the two specification tables below which we will use to tailor the correct multicompartment product for your needs. Table 1 Trunking Sizes Please scan and email or fax to your closest depot. Fitting Number: Table 2 Trunking Compartment sizes & Cable runs From... (State Measurements in mm) UNITRUNK (LISBURN) fax: +44 (0) 2892 625101 email: lisburn@unitrunk.co.uk UNITRUNK (IRELAND) fax: +353 (0) 1 8223533 email: dublin@unitrunk.ie UNITRUNK (SCOTLAND) fax: +44 (0) 1506 461969 email:...

Standard Trunking Multi Compartment Trunking MULTI-COMPARTMENT TRUNKING SYSTEMS CODE GUIDE STEP 2: CHOOSE PRODUCT POWDER COATED STEP 3: CHOOSE SIZE WIDTH SIZE CODE Lighting Trunking (3/3.5/4.5/6m lengths) Galvanised Steel Lid (Width Only) Trunking Coupling Dividing Fillet (loose) (Height Only) Gusset Bend (Inside Lid) GOB Gusset Bend (Outside Lid) Flared Flange Fire Barrier Clip Lid Clips (Strap and Stud) Flanged Coupling Cable Support Earth Link (Copper) x 10 SOE Sharp Elbow (OutsideLid) GTT Gusset Tee (Top lid) GIT GOT Gusset Tee (Outside Lid) STT Sharp Tee (Top Lid) SIT TCES Earth Link...