■■■IIIIII11■■■ Telford Copper Cylinders is a family run business which began trading in 1989 from the premises it still occupies today. The original factory has been extended on a number of occasions since then to keep up with the increased demand for its products. From the beginning Telford set out to manufacture a broad range of cylinders. Our copper division has developed from manufacturing traditional vented cylinders to now include commercial calorifiers and the award winning advanced Thermal Store units, which are available as manual fill, "Washing Machine", solar recovery and under-floor...

Index Selecting your cylinders 3-4 Stainless steel unvented cylinders 21 Domestic hot water cylinders 5 Material specification 22 Tappings charts 6 Installation 23 Typhoon CR 7 Technical specification Tornado 24-25 Standard vented specification 8 Technical specification Tempest 26-27 Combination tank 10 Variants 28 Maxistore cylinders 11 Alternative energy 29 Trident 12 Tempest solar cylinders 30-31 Calorifiers 13 Tristor renewable 32 Stainless steel vented Thermal store 14 15 Vented copper and stainless solar cylinder 33 How a thermal store works Tristor manual fill 16 17 The Telford complete...

Selecting the correct size of cylinder requires considration of a number of variables, including the volume of water needed, the energy source and the space available. Calculating the volume needed can be achieved by adding together the individual volumes of each appliance that uses hot water and how frequently it is used. The energy source is the next variable to consider, as it will have a direct impact on the cylinder size. All indirect cylinders have coils which are designed to allow the contents to be heated up in less than 25 minutes, given an adequate boiler size. High performance products,...

I INDIRECT Designed to be linked to a remote heat source, such as a gas boiler or coal tire. The water within the central heating system is heated by the remote heat source and is passed through the coil in the cylinder. As the primary normally operates at around 80°C. the heat is exchanged into the cylinder and warms the domestic water. Manufactured and fully approved to the latest British Standard specification BSI566:2002 (Part L). DIRECT When the only energy source available is electricity, a Direct pattern cylinder is the ideal product. The domestic water is "directly" heated by the immersion...

TF4S TF80 TF95 TF100 TF115 TF120 TF140 TF160 TF200 350 400 450 400 400 450 450 450 450 600 750 750 900 1050 900 1050 13» 1500 80 95 96 114 117 140 162 206 WhilBt Bacnticial anodeB romain an option on the standard product rarge. thsy canrot be specifed on Typhoon CR. Corrosion rsistant technotogy is at the heart ot thls rvision to the Typhoon CR product range. Orlglnally d驩signe! as an ultra-rapld recovery cyllnder It allows plumbers to Install small cyllnders as a space saving option, wfthout toslng performance. TypnoonCR tnctudes corrosion rsistant technotogy, thls enabies Telford to offer a...

A A A Dimensions < Notes: BS1566:2002 has within its scope both Indirect and Direct cylinders. Cylinders are designated as type D for Direct, G for Indirect cylinders suitable for both gravity and pumped primaries and type P for cylinders which are only suitable for pumped primary systems. Type P cylinders are new to the standard and are often high performance products offering improved performance over the G type. Within the Telford Copper Cylinder range, ref 2-11 are type G cylinders and suitable for both gravity and pumped primaries. Ref 0-1 and 12-14 are for pumped primaries only. Special...

Comblnatlon unlts have been deslgned lo combina the Cdd wator feed and the hot wator cyttnderkttoone unit There are many beoeftts to I natal ng a combinadon style cyllndef, Induding reduclng labour lime when Installlng the product and freelng up vaJuable roof space. The Incomtng suppty is connected dlrectty to the top section, thls In turn feeds the bottom(hot) section when water Is drawn from the hot tap. Our combinatton cyKnders are manutactured to BS3198 and can be ordered as Direct or Indirect variants. The Insulatlon of the division between hot and co(d wator sections ensuresthatheel transfert...

ers Maxistore was devetoped for use on an open-vented System h electric onty applkatons. The cyllnders carrylull Economy 7 accrditation and are manutactured to BS1666:2002 (PartLJ.To onsuro maximum pffirJancy tho eyllndor Ls fnamori twira, whlnh reduces the heat-loss values. Two skte entry Immersion heater connectjons are fltted as standard to maxJmtae the use oi Economy tarffietoctrterty. Later versions of the Maxistore rangs Incorporated a comblnation-style variant, to remove toe need for a teed tank In the roof Espace and ease Installation. Telford Copper Cyllnders can also suppty, as a cost...

r-'IH:.,,,; TRIDENT Conventional plumbing Systems require a separate cold water storage tank in addition to feed and expansion tanks. Thse tanks normally take up valuable roof space. The Trident cylinder removes the need forthis by incorporating them within the cylinder The appearance is similar to a combination unit, but also includes the feed tank to supply the central heating system.The time required to fit a Trident System is approximately three hours compared to around eight to install a conventional System. The number of fittings and materials needed for the installation are reduced dramatically...

Telford Copper Cylinders have introduced a range of Calorifiers for commercial and industrial applications. Available as Direct and Indirect variants, in capacities from 280 to 4500 litres. The cylinders are constructed from copper to the requirements of BS2870/1 deoxidised. Coil heater units or removable U-type batter units can be specified as shown. Immersion heaters can also be supplied to order. All Calorifiers are supplied with certified drawings and Test Certificates. Shells and heater units are fully tested prior to despatch to at least 11 /2 times the normal working pressure. Coil Heater...