Polyester pumping stations Manufactured by filament winding Mechanical and corrosion resistance 1 • Orthogonal filament winding consists in putting roving yarns on a mandrel along circumferential and longitudinal axes. 2 • This gives a material that offers maximum resistance on the load axes (60 to 70 % glass). 3 • We assemble the base on the shell, then add polyester lamination in order to obtain a perfect seal. The shell is made by filament winding. Polyester pumping station Mechanical resistance of the three techniques for the use of polyester

Polyester pumping stations Designed for communities Rain water and waste water The SRT station is perfectly suited for water pumping for any community such as: • Industry, • Town, • Subdivision, • Camp site, • Supermarket, etc... Volume pumped: 5 to 300 m3/h. The Range consists of 8 tank cross-sections: 1 • 1,2 • 1,4 • 1,6 • 1,8 • 2 • 2,4 et 2,9 m. For a height of 1 to 8 m. All our stations comply with the regulatory requirements of NF EN 12050 and are covered by a compliance certificate of the basic type (Test Report) granted by an authorized agency (CSTB). They can thus carry the mark. Electric...

Polyester pumping stations 3 possible configurations General description Base with polyester cover (in series execution) Hoist arm support Hoisting lug Glazed internal walls 2 meters of ducting for cable guidance to avoid grease accumulation Inlet sleeve Non return valve and shutter for each pump with gasket, performed to adapt to the nature and diameter of the pipe Aluminium ladder Polyester pumping station with detachable bracket (optional) Screen basket (option) Guiding bars Tank bottom Self-cleaning, integrated slope and reinforcement bars l Stainless stee hardware Anchoring feet On concrete...

Configuration with valve chamber Optional (see page 6) Valve chamber separate (optional) Non-return valve EPOXY-coated cast iron Flange valve EPOXY-coated cast iron with detachable bracket (optional) Screen basket (optional) Floats Guiding bars Lifting pumps Valve chamber Base with polyester cover Polyester pumping station Aluminium ladder Inside view with flange valves and non-return valves

Polyester pumping stations Products that meet your needs no matter what the site constraints are Photos of our material on site 1 • Screen basket with guiding bar 3 • Water hammer prevention tank mounted in the valve chamber 2 • Hoist arm 4 • Technical floor Polyester pumping station

Descriptions and references Galvanized steel screen basket OS366 Mesh size 50 mm. + galvanized steel guiding bar for 2 to 3 metre-high stations. OS368 Mesh size 50 mm. + galvanized steel guiding bar for 3.5 to 6 metre-high stations. Stainless steel screen basket OS365 Mesh size 50 mm. + stainless steel guiding bar for 2 to 3 metre-high stations. OS367 Mesh size 50 mm. + stainless steel guiding bar for 3.5 to 6 metre-high stations. Galvanised steel hoist arm Valve chamber □_A_ With non-return valves and shutters Galvanised steel base + Galvanised steel cover □_C Without cover for installation...

SRT m range Polyester pumping stations Control panels defined according to power CS208PV Control panels for two 400-Volt three-phase pumps (according to desired options) Polyester pumping station The all-in-one panel is self-extinguishing and IP66 watertight. It is made of fiberglass-reinforced polyester, hot pressed, with smooth finish. All panels are fitted with 2 doors: 1 •One inside door (A) housing all the control devices 2 • One outer door with 2 1242E-type locks with key - either transparent (B) in tempered glass, ref.: CS20xPV - or solid (C), ref.: CS20xPP Our control panels are installed...

Equipment and options for control panels Descriptions and references □ SIA05 For anti-HsS treatment (Please ask for our SIA05 documentation) Options on control panels □ _ OS332 Voltmeter with measurements on 3 phases □ . OS313 Inversion and missing phase protection relay OS343 24-Volt hand lamp + 10 m wire OS335 Heating resistor £ OS371 Differential switch, 30 mA max 25 A f] OS372 Differential switch, 300 mA max 25 A £ OS373 Differential switch, 30 mA max 40 A d OS374 Differential switch, 300 mA max 40 A £ OS375 Differential switch, 30 mA max 63 A £ OS376 Differential switch, 300 mA max 63 A...

range Polyester pumping stations Very rapid installation: the station is delivered ready to install Inlet and outlet sleeves made to the dimensions requested by the customer. Installation under grass Dig a hole according to the size of the tank. Place the earth rod. Make a 20-cm thick concrete slab at the bottom of the pit. Place the station on the slab. Anchor the fastening feet of the station to the slab. Connect up the pipes and fill with 10-15 mm gravel. Installation under a road The station must be buried 20 cm below the surrounding land. Pass the cable duct through to the control panel....

Designing a polyester pumping station requires careful analysis. We have developed a computer programme with which the characteristics of a station can be defined very quickly. To enable us to meet your needs precisely, please photocopy this page, fill it in and fax it to us at +33 (0)2 33 56 61 93. Nature of the Water: □ Domestic Waste water □ Rain water □ Industrial Waste water Volume: or Number of users: Power Supply: □ Three-phase 400 V □ Single-phase 230 V. Land measurements (see diagram below): A Land level: B Highest point:_ C Inlet level: D Discharge length:_

Techneaueau . TechnTechnea^y Equip* in t n I • d • I o I WATER MANAGEMENT • Water PRE-TREATMENT - Oil interceptors - Grease / starch separators • Water TREATMENT - Settle solids interceptors • HYDRAULIC ACCESSORIES - Flow controllers - Penstocks • PUMPING STATIONS - Small communities - Large communities FLOOR EQUIPMENT FLOOR ACCESS COVERS STAINLESS STEEL FLOOR DRAINS & CHANNELS