Installation & maintenance instructions

Installation & maintenance instructions ECODUR – Multilayer engineered plank For optimum advice, fulfillment of all inspection obligations and professional installation, please contact an installation specialist. The specifications of the currently valid standards, the general rules of technology and the guidelines on the manufacturer's data sheets and instructions apply to the installation and subsequent use. In order to obtain a warranty and the best installation results, the following installation and regulations must be observed without fail. It is extremely important to read and understand...

In addition to the moisture test, also observe the requirements for the flatness of the subfloor. According to ÖNORM DIN 18202 "Tolerances in building construction", these are a maximum deviation of 4 mm at an inside micrometer of 1 m. With a measuring point distance of e.g. 1 m, the subfloor is to be allowed a maximum allowance of 4 mm according to the standard. Measuring point distance Inside micrometer ATTENTION! – 3 mm for increased requirements. According to ÖNORM B 2218 "Installation of wooden floors" – the flatness tolerances according to ÖNORM DIN 18202 – table 3, line 4 "increased requirements"...

Old flooring ECODUR can be installed on most hard coverings. Level the joints of ceramic tiles with suitable leveling or filling compound according to manufacturer's specifications. Remove all textile and other soft coverings before laying ECODUR. Floor Installation Floating installation Start installation of the floor only after all craftsmen from other trades have left. Before installation, holes, cracks and other damage should be closed with suitable materials. It is recommended to open several packages at the same time and mix the planks by color and texture to achieve a uniform overall appearance....

Then install plank by plank according to the same scheme. The remaining piece of a row can be used as the beginning of the new row if it is at least 40 cm long. The face offset must also always be at least 40 cm. During the entire installation, the elements must be checked for material defects as well as color and structure deviations. Elements with visible material defects should not be installed. Installed elements with visible material defects are excluded from complaints! Cut the elements of the last row to size. Proceed as before when locking the end faces. You can achieve a permanent connection...

Cleaning and maintenance Cleaning varnished wooden surfaces Remove coarse dirt with a mop, hair broom or vacuum cleaner, fine dust with lukewarm water! For sealed floors (to avoid graying of the surface) please use parquet cleaner. Application instructions are indicated on the product and must be followed. Wring out the cloth firmly and clean your parquet floor with a damp cloth only. Heavy soiling, stains or rubber marks can usually be removed by "erasing". To remove stains, solvents such as turpentine substitute, white gasoline or methylated spirits can also be used with caution. ATTENTION!:...

Refinishing recommendation for Stöckl ECODUR flooring PALLMANN CLEAN (water-based cleaning agent) • Container must be at the recommended room temperature (20 °C) before use. • Dilute 1 part PALLMANN CLEAN with 3 parts water. • Apply evenly to the entire surface with the PALLMANN FLOOR MOP. Allow to act for approx. 2 - 5 minutes and brush off with the PALLMANN TURBO SCRUBBER with GREEN BRUSH ROLLER. Work the edge manually with green pad. • Take up the loosened dirt with the PALLMANN TURBO SCRUBBER and wipe thoroughly once with clear water and renew the wiping liquor as soon as possible. In the...

Room comfort climate The optimum combination, i.e. the right interplay between relative humidity and temperature is the key to a healthy room comfort climate! Depending on the season, a relative humidity of 45 – 65 % and a room temperature of 18 – 22° C are recommended. In addition, the wood floor surface temperature of max. 28° C should NOT be exceeded. At these values or conditions, the natural wood properties such as joints, cracks or cupping will occur to a minor extent. Wood is a natural material and changes its shape in case of longer deviation from these given values (especially humidity)....

With the publication of this edition, all previous versions lose their validity! With this information, we want to advise you to the best of our knowledge based on our tests, experience and standards applied. The conditions on site are not known to STÖCKL and must be checked by a specialist and the structure adapted if necessary. Valid for all pages. Stöckl GmbH I Heide 25 | 3331 Kematen an der Ybbs I www.stoeckl.com