TMS®
4Pages

TECHNICAL DATA SHEET n° INSFR001/i cancels and replaces n° INSFR001/h TMS TMS is a rigid polyurethane (PUR) foam thermal insulation panel for buildings, covered with a facer on each side. User application TMS is intended to be used for: • Low, intermediate, and high floors thermal insulation (including attic floors): - under screed with a base of hydraulic binders (Code of Practice & standard NF DTU 26.2) or under sealed flooring tiles (NF DTU 52.1), in compliance with NF DTU 52.10 for insulating undercoats or under a fluid screed covered by a valid Technical Approval, under hot water operated underfloor heated floor, in compliance with requirement of NF DTU 65.14 or under an electric radiant heated floor in compliance with the Technical Requirements Booklet CPT PRE (CSTB eBook n°3606-V3), under slab-on grad in compliance with Code of Practice & standard NF P 11-213-1 (DTU 13.3), under supported slab in compliance with Eurocode 2 and Code of Practice & standard NF P18-201 (DTU 21), under wood-based panels floating floor, in compliance with standard NF P 63-203 (DTU 51.3), over non-fitted out attic floors for residential building, for garage celling and basement of 1st and 2nd single-unit residential building categories, in compliance with the "Guide to interior insulation of residential buildings from the point of view of risks in the event of fire” published by the CSTB (see installation paragraph). • Internal thermal insulation for vertical walls of new or old building. The wall is thermally insulated by using TMS panels associated with a counter-partition: - With gypsum plasterboard with a metal frame, in compliance with Code of Practice & standard DTU 25.41, plaster tiles, in compliance with DTU 25.31, terracotta clay bricks, concrete blocks, cellular concrete or natural stone blocks, in compliance with DTU 20.13. Composition TMS Rigid polyurethane foam Cream colour Density: 32,5 ± 2,5 kg/m3 Upper and lower facer Multilayer marked by a grid of 10 cm steps Page 1 / 4 SOPREMA SAS with a Capital of 50 0 00 000 € - Headquarter: 14 rue de Saint -Nazaire – 67100 STRASBOURG – FRANCE Postal adress: CS 60121 67025 STRASBOURG CEDEX. RCS STRASBO URG: 314 527 557.SOPREMA reserves the right to amend the composition of its material and consequently their prices, without prior notice. For this reason, all orders will be accepted only in accordance with the conditions and technical specifications in force at the date of order. Tel: + 33 (0) 3 88 79 84 84 – Fax: + 33 (0) 3 88 79 84 85 www.soprema.com - email: exp

TECHNICAL DATA SHEET n° INSFR001/i cancels and replaces n° INSFR001/h Characteristics - CE marking TMS is a thermal insulation panel for buildings in compliance with EN 13165 “Manufactured rigid polyurethane foam (PU) products”. Essential characteristics Harmonised Technical Specification Thermal conductivity – λD (W/(m.K)) Thickness – d (mm) Thermal resistance – RD (m².K/W) Thickness tolerance Durability of reaction to fire against heat exposure, weathering, ageing/degradation Durability of thermal resistance against heat exposure, weathering, ageing/ and degradation Durability...

TECHNICAL DATA SHEET n° INSFR001/i cancels and replaces n° INSFR001/h Characteristics (off CE marking) Characteristics Floor classification Critical strength at service Deformation at service Impact insulation class (under screed) Performances SC1a2Ch (21 to 140 mm), SC1b1 (21 to 100 mm) From 25 to 160 mm: Rcs ≥ 105 kPa / dsmin = 1,3 % - dsmax = 1.6 % Module ES = 4.34 MPa ΔLw = 17 dB for thickness = 21 mm ΔLw = 18 dB for thickness = 56 mm ΔLw = 19 dB for thickness = 120 mm ACERMI* certificate Classification of emission for volatile substances in indoor air *ACERMI: French association for...

TECHNICAL DATA SHEET n° INSFR001/i cancels and replaces n° INSFR001/h • for garage celling and basement of 1st and 2nd single-unit residential building categories, in compliance with the "Guide to interior insulation of residential buildings from the point of view of risks in the event of fire” published by the CSTB and DTU 25.41. TMS panels are mechanically fastened. They are protected by a “fireproof” BA13 gypsum plasterboard (at least 12.5 mm thickness) mechanically fastened on metallic frame with 60 cm spacing. Using conditions of TMS insulation panels for vertical parts TMS panels are...