makes you independent Solar Technology © www.fotolia.com

than satisfied

The Sun − Heat Free of Charge Did you know, ... Atmosphere Orbit ... that the sun delivers enough power in only 3 hours to cover the annual energy demand of the entire planet? Only a part of the sun’s rays can be used for energy WITHOU T LIGHT NO HEA T production YOUR BENEFIT Reflection through the clouds Scattering in the denser atmosphere Absorption in the atmosphere Diffusion radiation diffused radiation This part of the sun’s radiation is used for heating with solar collector panels. Earth Direct radiation direct radiation Ground reflection The average annual global radiation in Central Europe...

... always toward the south would be ideal When designing your solar system the positioning of the collectors plays an important role. An southern alignment (optimal at 10° South-West) and a roof-pitch of 30° to 45° is desirable. In the event of considerable deviations the reduced yield can be compensated for by enlarging the collec- YOUR BENEFIT At a westerly alignment and a 30° roof pitch the CPC-collector from SOLARFOCUS will only achieve 80 % of the yield that could be gained from the optimal southern alignment. tor surface. Roof inclination (degrees) 90 80 70 60 50 90 WEST 40 30 20 10 0...

CPC-collector... the crucial differences: Why the structure of the collector should be important to you: Because environmental factors, such as wind and weather, UV radiation, snow loads and excessive variations in temperature affect the collector for decades. # The 1.5 mm leak-proof welded aluminium tank without vent holes forms the "foundation". # Air and waterproof design without air holes and rivets protect the interior of your collector for # High-selective coated copper absorber with ultrasonic welded heat transfer medium pipe. # The floating absorber which is coated on both sides guarantees...

The surface sealing joints (7) # 1/2" external thread with flat-faced gasket. # The surface seals contacting the interior and exterior side of the tray are screwed in plane-parallel with brass nuts and hermetically seal the tray. No environmentally vulnerable rubber or plastic seals. Allows simple connection of the collectors. # Negative pressure relief valve for pressure compensation. The air expands at the first warm-up of the interior of the collector - and excess pressure develops. The valve opens and the air can escape. When the air cools, the valve closes and a vacuum develops in the interior...

CPC-collector... not only for summer The angle of the sun on the collector surface changes continually with the Earth's movement. The greatest share of the sun's rays will therefore fall at an angle onto the collector. ... designates the energy absorption by the absorber on both sides with direct solar radiation. ... means still usable temperatures with flat, weak solar Basically simple, ingeniously inventive. The CPC-collector technology from SOLARFOCUS allows the efficient use of even flat penetrating solar rays. This is important during the transitional period (spring and autumn), since up...

CPC-collector - Technical Data Heat loss factor K1/K2 Conversion factor (according to aperture surface) Incidance angle modifier 30° / 50° Diffusion factor (Kdiff) Heat capacity Flow rate Glass cover 4 mm solar safety glass The right solution for every case All models can be used in a vertical or horizontal installation.

SunnyMne ... the flat collector Why the structure of the collector should be important to you: Because environmental effects, such as wind and weather, UV radiation, snow loads and excessive variations in temperature affect the collector for decades. # The welded tight aluminium tank forms the "foundation". # The high quality manufacturing process protects the inside of the collector for decades. # The highly selective solid surfaced absorber (blue-line) stands out for its level of solar absorption of approx. 95% and level of heat emission of approx. 5%. # The absorber unit which is fitted so...

G 1/2” external thread with butt joint. G The surface joints located on the inside and outside of the tray are screwed down parallel to the casing with brass bolts, in such a way that they hermetically seal the tray. No rubber or plastic seals that wear out in outdoor conditions. Single connection of the collector’ pipes. 8 6 2 7 4 makes you independent The sealed connections between surfaces (6) 5 Rear wall insulation (7) G 50 mm of mineral wool with low binding content. G As a result of the low proportion of binding agents that exist in the mineral wool insulation releases almost “zero gases”....

Sunnyline - Technical Data Heat loss factor Conversion factor Glass cover Flat plate collector 4 mm solar safety glass Suitable for heating drinking water and swimming pools, and for partial solar ambient heating. The right solution for every case All models can be used in a vertical or horizontal instal- Special requirements on request: e.g. pipe outlet on y Can be used anywhere: Hot water, auxiliary heating, swimming pool heating / Only high quality corrosion and oxidation-resistant materials used / Welded aluminium casing - protects the interior of the collector for many decades / Highly selective...

Planning and design of a solar system Collector Area Storage Tank Hyko Thermal stratified tank Hyko Thermal stratified tank tified tank These design recommendations should assist you in planning your system. The assumed values are for guidance only. Important parameters, such as hot water consumption, roof incline and aspect must be given individual consideration during the plan- ning phase. The house energy index and type of heating are decisi- ve in determining the coverage for partial solar heating installations. SOLARFOCUS, thanks to hundreds of standard schematics, can aid in your system,...

Plug-IN - Domestic Hot Water Tank YOUR BENEFITS # DHW tank with pre-fitted pump set and solar control # Dual coil solar storage tank # Also available with high efficiency pump Avoid assembly errors with the pre-assembled solar control unit and pump set. Capacity Diameter Diameter Total Upper heating Lower heating Weight Tilted El. screw-in heating without insulation with insulation height coil coil height 6/4" possible