*myarchiexpo

SoLIMAX

Product catalog summary

Introduction
The SoLIMAX safety position sensor is a high-tech safety component exclusively offered by SODIMAS. It is certified SIL3 and complies with the EN 81-1 A3 standard when used with the Quick Install controller.

Specifications

Measurement Principle: Absolute linear
Max Speed: 3 m/s in Quick Install (up to 10 m/s)
Resolution: 0.0625 mm
Communication: CAN Open bus
Dimensions: H370 x L85 x D39 mm, Weight: 0.9 kg
Standards: EN 81-1 + A3, EN 61-508, EN 12015/12016 (EMC)
Certification: TUV-A-AT-1/12/316CEES
Temperature Range: -20°C to 70°C
Protection: IP54
Vibration Standards: EN 60068-2-6, EN 60068-2-27, EN 60068-2-29

Safety Features
The sensor ensures safety by monitoring:

Position of travel limits and inspection
Deceleration control
Zone amendment A3
Levelling and early opening zones
Speed control in various modes
Overspeed protection
Absolute car position accuracy of 2 mm

Facility and Installation
The system is designed for fast installation with a single sensor on the roof and a tape in the shaft, reducing setup time and allowing for margin in car travel within guide rails.

Comfort and Maintenance
The SoLIMAX sensor provides silent operation by eliminating noise from standard sensors and contact shocks. It offers fast and accurate information for speed and position control. Maintenance is simplified by reducing the need for mechanical and electrical checks, and minimizing potential failures through fewer electrical contacts.

Conclusion
The SoLIMAX safety position sensor, when used with the QUICK INSTALL controller, offers a certified, high-performance, and efficient solution for safety in lift systems.

Catalog excerpts

SELECTION / DETECTION Safety position sensor

Open the catalog to page 1

From now on “High Tech” safety exclusively by SODIMAS Components safety certified SIL3 No. TUV-A-AT-1/12/316CEES and compliant with the EN 81-1 A3 standard when used with the Quick Install controlle

Open the catalog to page 3

BSODIMAS'ascenseunsLOCATIONFEATURES Sensor and safety box - Measure / principle : absolute linear - Max. speed. 3 m/s in Quick Install (max 10 m/s ) - Resolution : 0.0625 mm - Communication : Can Open bus - Space required for sensor : H370 x L85 x D39 - Weight: 0.9 kg - Diagnostic : Visualisation LEDs - Standards : EN 81-1 + A3 - EN 61-508 - EN 12015/12016 (EMC) - Certification : TUV-A-AT-1/12/316CEES - Compliant with 95/16/EC lift directive appendix 5 - Application temperature : - 20°C to 70°C - Protection : IP54 (EN 60529) - Vibration : EN 60068-2-6 /EN 60068-2-27, EN 60068-2-29 - Internal...

Open the catalog to page 4

SAFET Y Component safety certified SIL3 No. TUV-A-AT-1/12/316CEES and compliant with standard EN 81-1 A3, it integrates and checks the safety of : - the position of the extreme limits of travel, inspection, deceleration control - the zone amendment A3 - the levelling and early opening zone - speed control in maintenance, nominal mode and in the door zone - overspeed - the absolute position of the car to an accuracy of 2 mm and the actual attitude by means of the coded stainless steel tape in the shaft (position saved even after a prolonged cut off of the current). FACILIT Y - Fast, only one sensor...

Open the catalog to page 5

Siège social / Head office 11 rue Ampère 26600 Pont de l’Isère FRANCE +33(0)4 75 84 86 00 +33(0)4 75 84 67 30 e-mail : [email protected] FABRICATION FRANÇAISE UK SODIMAS design 07/2013 - 27SO053P00007EN - Photographs and illustrations not contractuals. Modifications without prior notice. Speechless reproduction even parti

Open the catalog to page 6