sikkEnsWOOD COATINGS Product description Drying Waterborne, opaque, satin gloss, two-component mid and top coat for front doors. Must be interlaced with WV 850 before processing. Only for unweathered wooden constructions, e.g. wood-aluminium constructions and other wooden surfaces in the interior, it is not necessary to add WV 850. - good flow - good mechanical resistance - tested according to DIN EN 71 Part 3 "Safety of toys” Drying at: Standard atmosphere: 23°C / 50% rel. humidity Dust dry approx. 60 minutes Sandable approx. 4 hours Recoatable approx. 4 - 6 hours Forced at 40°C approx. 30 minutes approx. 60 minutes approx. 1 - 2 hours The drying process of the coating depends on the applied film may be delayed when using timber with a high extractive content damp/cold conditions. During the drying process, always ensure temperature and ventilation. If the drying conditions are not met, within the coating cannot be excluded. Cleaning of equipment Clean with water immediately after use and, if required, add somu commercially available washing-up liquid or ST 830. ckness s or dry for adeq damage years; Storage The minimum shelf life in the unopened original container is two temperature +5 - +30 ° C. After expiry of the BBD, the product may still be processable. properties may differ from "fresh" material. For that reason, the expired material with particular attention. Started containers must be closed carefully! Store in a cool but frost-free place. oduct apply Disposal Only empty containers may be recycled. Dispose of material residues according to local regulations. The EC waste code applicable to such material is: 08 01 12 Safety Data Sheet Further data in the Material Safety Data Sheet according to 91/155/EEC www.sikkens-wood-coatings.com Downloads Safety Data Sheets Warning Before use, read the identification and product information. Always follow customary protection measures, even when working with low emission products. VOC Directive EU limit value for this product (cat. A/d): 150 g/l (2007)/130 g/l (2010). This product contains max. 50 g/l VOC. General instructions The wood moisture content for the application of Sikkens coating system: should be between 12 % and 15 %. The selected wood, the design and applied layer thicknesses must comply with current technical standards horizontal surfaces shall be bevelled by 15 ° and all edges shal be rou with a radius of at least 2 mm. Joints and open end grains must be sealei prevent the ingress of water into the structure. The substrates must be from dust and grease. The selection and application of the coating, esp: the colour shade, is important, too. Dark coatings in the exterior may lea elevated surface temperature (up to 80 °C). For use in technical industrial companies. Only to be used in api recommended Sikkens Wood Coatings coating systems. Products from AkzoNobel Wood Coatings are exclusively produced for professional and industrial users, who have a basic knowledge of the handling and application of chemical/technical products for surface design. The processing instructions for reaching the qualities given in the leaflets should be regarded as non-binding recommendations and do not constitute any warranty. The: recommendations are based on our experiences, including test series, and should facilitate and promote the work of our clients. Any potential deviation from ideal working conditions is within the responsibility of our clients and may affect the (end) result of the application. The purchaser is not relieved from his duties to inspect the product and its suitability for the surface to be processed, preferably trough trial processing. If in any doubt as to the handling or processing of the purchased product, our material experts as well as our application and laboratory technicians will help you to the best of their ability. AkzoNobel, of course, guarantees an impeccable quality of its products in its product specifications, yet the use thereof lies entirely within the responsibility of the purchaser. As ong as w; have not guaranteed - in writing - the specific characteristics and suitability of a product for a contractually agreed purpose, any advice or information given regarding the application or handling, even if the advice or information is given to the best of our knowledge, will not be binding nor will it constitute a warranty. AkzoNobel’s liability for the use of its products by its customers is limited in its General Sales and Delivery Conditions, to which the purchaser is hereby referred. The applicable version of the Technical Data Sheet for this product can be downloaded from our websites Previous versions of the Technical Data Sheets are rendered void with the issue of a new one. Date of issue:2017-08-26 EMEA HQ Akzo Nobel Hilden GmbH • Dusseldorfer Str. 96 - 100 • 40721 Hilden • Deutschland • www.akzonobel.com/wood

Notes The coating system mentioned here is only an example; other systems are possible. Please refer to the relevant Technical Data Sheets and ask your Sikkens Wood Coatings Sales Representative or the factory for advice about coating systems. All external materials coming into contact with the coating system (e.g. putty, adhesive tapes, sealants, cleaners, etc.) must be tested for compatibility by the user. With some wood species, discolouration can appear due to natural wood extractives. These discolourations can be avoided by using an isolating sealer and mid-coat. Coating recommendation When...