5ikkEn5WOOD COATINGS Rubbol WF 318 Product description Waterborne, satin gloss paint for maintenance of the coating on windows and doors, exterior and interior. - good edge covering - good hiding power - easy to apply - Safety of Toys (according to EN 71, part 3) Drying times Drying at 23 °C / 50 % R.H. Dust dry: after approx. 30 minutes Sandable: after approx. 4 hours Recoatable: after approx. 4 - 6 hours waterborne The drying process of the coating depends on the applied wet film thickness and can extend when using timber with a high extract contents or drying in damp/cold conditions. During the drying process one should ensure for adequate temperature and ventilation. If the drying conditions are not upheld, damages within the coating cannot be warranted. Cleaning of equipment Clean directly after use with water, if needed with washing up liquid or with ST 830. StorageThe minimum storage stability of sealed containers is 2 years. Storage temperature: +5 - +30 °C. After ending of the storage time the product still can be usable, but some attributes may vary from new product. Therefore such over-stored product has to be applied with special attention. Opened cans must be sealed correctly! Store in a cool but frost-protected area. Disposal Only residue emptied cans can be disposed via recycling. Liquid wastes must be disposed of according to national regulations or according to EU-disposal key 08 01 12. Hazard identification In accordance with EC guide lines - Material safety data sheet, point 15. Warning Before use, read the identification and product information. Even when working with low emission products one should take care of the customary protection measures. General instructionsThe wood moisture content for the application of Sikkens coating systems should be between 12 % and 15 %. According to the guidelines for window coating systems, published by the Federal German Committee for Paint and Material Value Protection (Instruction Leaflet No. 18), of VOB, Part C, DIN 18363, and the recommendations of the German Institute for Window Technology e.V. in Rosenheim, all wooden constructions in buildings must be coated on all sides with at least one primer and one intermediate coat (minimum dry film thickness 30 |jm) before they are incorporated in buildings. The choice and use of the coating system, especially the colour shade, should also be taken into account. Darker shades can increase the surface temperature (up to 80 C). For use in a technical industrial companies and exclusively released for Sikkens systems recomondations. With some wood species, especially hardwoods, discolouration can appear due to natural wood extractives. VOC guideline EU limit value for this product (Kat. A/d): 150 g/l (2007)/130 g/l (2010). This product contains max. 50 g/l VOC. Relevant information Rubbol WF 318 is the corresponding maintenance product for the industrial coating with Rubbol WF 378 or Rubbol WF 387. Please observe the relevant Technical Data Sheets or seek advice from the Sikkens sales representative or contact the technical centre. Coating recommendation This product must be brushed 3X on raw, base coated timber to obtain a similar,original dry thickness compared to a spray application. Renovation systems: Open joints and small cracks can be closed with Kodrin WV Spachtel. Substrate preperation: non intact, old and loose coatings must be completely removed. Intact coating should be completely sanded. Raw wood must be impregnated where necessary. Akzo Nobel Industrial Coatings Ltd Akzo Nobel Industrial Coatings Ltd Akzo Nobel Wood Coatings GmbH Unit 4a, Mercer Way, Shadsworth Bus Pk Unit 4a, Mercer Way, Shadsworth Bus Pk Dusseldorfer StraSe 96-100 Blackburn, Lancs, BB12QZ Blackburn, Lancs, BB12QZ D-40721 Hilden UNITED KINGDOM Rep of IRELAND GERMANY 1/2 generated: 18.07.2017 last change: 30.08.2011

System structure: Dimensional stable wooden constructions Impregnation All details on our products contained in this publication do not represent details of the quality of the goods. The quality, suitability, qualification and function intended use of our goods shall be determined exclusively in accordance with the product descriptions based on the respective sales agreements. \n each case, deviations typical of the sector shall be admissible, unless agreed in writing otherwise. All details correspond to todays state of technology. We make no claim as to the completness of the stated coating installations;...