5ikkEn5WOOD COATINGS Cetol WP 562 BPD Product description Waterborne, translucent base stain (fluid timber protecting agent) with blue stain fungi protection for wooden constructions, exterior. - ready to use - deep penetration - good run-off properties - coloring Active ingredientThe substances are notified according to the guildlines 98/8/EG. and correspond to the requirements of the examination EN 152.1 against blue stain fungi. 0,6 g/100 g propinylbutylcarbamate iodine 0,9 g/100 g propiconazol BAuA-registration Nr. N-40652 Wood protection agents must be registered according to the BPD. (BPD = Biocide Product Directive) Uptake consumption The examination follows the uptake value: 120-160 ml/m2 i.e. 123-164 g/m2 for timber in the resistance classes 3-5 Colour With the choice of the different translucent colours, one should observe the Rosenheimer paint classification table. All translucent colours can be mixed with each other. The optical appearence of different systems can differ depending on substrate and wet film thicknesses, for this reason one should make trials before application. Dark translucent colours give better weather durability than light colours. Colourless systems are not suitable for exterior. Timbers which contain extractives i.e. Oak, Larch or tropical woods can cause discolouring - these can appear after weathering. Translucent, colour tints i.e. from the Joinery Colour Collection. Binder type Acrylic Copolymer Pigments Light genuine, weather resistant translucent pigments Packaging 5 L, 20 L, 100 L Processing Working viscosity is approx. 11 seconds in a DIN cup 4 mm i.e. approx. 23 - 25 seconds in a ISO cup 3 mm at 20° C material temperature. Brushing machine, vacuum coater EU-Regulation No. 528/2012: This product must only be used in fully automated dipping processes where all steps in the treatment and drying process are mechanised and no manual handling takes place, including when the treated articles are transported through the dip tank to the draining/drying and storage (if not already surface dry before moving to storage). Where appropriate, the wooden articles to be treated must be fully secured (e.g. via tension belts or clamping devices) prior to treatment and during the dipping process, and must not be manually handled until after the treated articles are surface dry. automated dipping, flow-coating Consumption 50 - 160 ml/m2, depending on application method, type and absorption properties of wood (exact values must be Hazard identification In accordance with EC guide lines - Material safety data sheet, point 15. Warning The Impregnation serves as a protection of none statically subjected wooden constructions without earth contact, exterior, against blue stain and rot according to DIN 68800, part 3. Not for use with wood which has got direct contact with food or food preparation. Only for the use of qualified enterprises Dipping tanks or reservoirs: when using metal reservoirs, we recommend using None rusting steel i.e. V2A, the use of other materials can lead to corrosion. Akzo Nobel Industrial Coatings Ltd Unit 4a, Mercer Way, Shadsworth Bus Pk Akzo Nobel Industrial Coatings Ltd Unit 4a, Mercer Way, Shadsworth Bus Pk Akzo Nobel Wood Coatings GmbH Dusseldorfer StraSe 96-100 UNITED KINGDOM Rep of IRELAND GERMANY Blackburn, Lancs, BB12QZ Blackburn, Lancs, BB12QZ D-40721 Hilden 1/2 generated: 20.06.2017 last change: 28.07.2011

Biocide products must be handled carefully Before use, read the identification and product information. Even when working with low emission products one should take care of the customary protection measures. Not to be used near waterways. The fluid must not entre water. Wood preservatives contain biozid substances for the protection against pest control. They are only to be used according to instructions and in permitted working areas. Misuse can lead to a hazard to health. Coating recommendation When using the light shades on timber with high extract contents (i.e. Meranti, Larch, Oak) discolouration...