System controller for integration of BACnet/MSTP, Modbus, and KNX PL-Link devices ● ● ● ● ● ● ● ● ● ● System controller to integrate BACnet MS/TP, Modbus, and KNX PL-Link devices Communication BACnet/IP (BTL certified) 2-port Ethernet switch for low-cost cabling Integration of Modbus data points via RTU and / or TCP Integration of BACnet MS/TP devices KNX PL-Link bus to connect sensors and operator units (including bus power) WLAN interface for engineering and commissioning Operating voltage AC 24 V Mounted on standard rails or on the wall Plug-in screw terminal blocks

Functions Freely programmable system controller. ● System functions (alarming, scheduling, trending, access protection with individually definable user profiles and categories) ● System controller for system networks with PXC3, PXC4, PXC5, PXC7 and DXR controllers over BACnet/IP, BACnet/SC, or BACnet MS/TP ● Integrates third-party devices and systems ● The following functions are available with KNX PL-Link bus: – Communication with room operator units and sensors. ● ● ● ● ● ● ● – Plug-and-play connection of Siemens field devices with KNX PL-Link. Generic object viewer for data points of several...

Desigo Control Point Description BACnet touch panels with integrated web server Touch panels clients with data storage in web server PXG3.Wx00-1 BACnet/IP web server with standard functionality BACnet/IP web server with extended functionality Technical and mechanical design The compact build allows for mounting the devices on a standard rail or a wall. 5 Plug-in terminal blocks with screw terminals Digital input, for future use Plug-in terminal block with screw terminals M-bus, for future use Plug-in terminal block with screw terminals COM1 / COM2 (MS/TP or Modbus) Plug-in terminal block with...

Continuously ON Continuously OFF Flashing Link active No connection Network traffic Link 100 Mbps Link 10 Mbps Continuously ON Continuously OFF Flashing Device operational Device not operational Start-up or program halted Continuously OFF Continuously ON Rapid flashing OK HW or SW fault Firmware or application missing/corrupted Connection to the cloud OK No connection to the cloud Optional battery OK Optional battery empty - replace Communication No communication to subsystem Communication No communication to subsystem Flashing per wink command Identification of the device after receipt of wink...

Product documentation Related documents such as the environmental declarations, CE declarations, etc., can be downloaded from the following Internet address: www.siemens.com/bt/download Notes Safety CAUTION National safety regulations Failure to comply with national safety regulations may result in personal injury and property damage. ● Observe national provisions and comply with the appropriate safety regulations. Mounting position and ambient temperature The devices can be snapped onto standard rails or screwed onto a flat surface. Plug-in screw terminals connect power and interfaces. Ambient...

Technical data Power supply Operating voltage (24 V~, ⏊, Functional ground (US) Functional earth The terminal for the functional ground must be connected on the installation side with the building grounding system (PE). Screw terminals for wire cross sections up to Internal fusing External supply line fusing (EU) Non-renewable fuse max. 10 A slow-blow or circuit breaker max. 13 A Tripping characteristic B, C, D per EN 60898 or Power supply with current limitation of max. 10 A Power consumption (for transformer planning) Full load Base load (without loading by KNX PL-Link and M-Bus) M-Bus supply,...

Screw terminals, plug-in Cu-wire or Cu-strand with wire end sleeve Cu-strand without wire end sleeve Stripping length Slot screws, screwdriver size 1 with shaft ø = 3 mm The two COM interfaces can be used either for Modbus or for MS/TP, according to configuration. Modbus RTU interface Interface type Baud rate 120 Ohm, switchable with DIP switch 270 Ohm pull-up/pull-down resistances, switchable with DIP switch Cabling (in-house cabling only) 3-wire cable, shielded cable recommended (shield must be connected to building earth in the mounting panel) Cable length Short-circuit proof Protection against...

WLAN interface Interface type Wireless access point Supported standards Frequency band WLAN channels Maximum radio-frequency power Distance (unobstructed field) Device pairing Activation / Deactivation with service button Automatic switch off after 10 minutes if no WLAN-client is connected. Optionally, for cyber security reasons, the WLAN can be permanently disabled via configuration. Default SSID and WLAN password: Scan the QR code. It will show something like WIFI:S:PXC5.E003_0000550;T:WPA;P:1400052738;; Then SSID = PXC5.E003_0000550 and password = 1400052738 Determine manually: Use the information...

Standards, directives and approvals Product standards Product family standard For residential, commercial, and industrial environments Eurasian compliance UL/cUL approbation (US / Canada) BACnet. Environmental compatibility The product environmental declaration 1) contains data on environmentally compatible product design and assessments (RoHS compliance, materials composition, packaging, environmental benefit, disposal). Documents can be downloaded at http://siemens.com/bt/download. FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device,...

Radiofrequency radiation exposure statement This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. Housing Color top/bottom Dimensions Weight without/with packaging 10 Siemens Schweiz AG Smart Infrastructure RAL 7035 (light grey) / RAL 7016 (anthracite grey)

Connection terminals Description 2 x RJ45 interface for Ethernet with switch Functional ground must be connected on the installation side with the building grounding system (PE). Digital input (for future use) Interface EIA-485 (Modbus RTU and MS/TP) M-bus interface (for future use) Warranty The application-specific technical data is guaranteed only in combination with the Siemens products listed in the 'Device combinations' section. If third-party products are used, any guarantee provided by Siemens will be invalidated. Siemens Schweiz AG Smart Infrastructure