 Water‐based acrylic  Cool Feel technology reduces exterior concrete surface temperature by 20 degrees F.  Highly resistant to pool chemicals and UV rays  Tintable for custom color options  Flat finish PRODUCT DESCRIPTION H&C® ACRYLA‐DECK™ Hi‐Build Deck coating with COOL FEEL™ TECHNOLOGY is a high quality hi‐build latex deck coating that provides superior protection and beauty for both exterior and interior concrete. It may be applied to bare concrete or previously painted surfaces. H&C® ACRYLA‐DECK™ Hi‐Build Deck coating with COOL FEEL™ TECHNOLOGY is designed to reduce the temperature of concrete surfaces exposed to UV rays by up to 20 degrees F.* * Temperature reduction may differ due to factors such as: ambient temperature, time of day and the amount of direct sunlight on the surface. FEATURES & BENEFITS  Provides a durable finish that extends the life of concrete and masonry surfaces.  COOL FEEL™ TECHNOLOGY designed to reduce the temperature of concrete surfaces exposed to UV rays by up to 20 degrees F.  Highly resistant to pool chemicals and many other household chemicals for long lasting beauty and protection.  Hi‐Build coating limits the surface from becoming slippery.  Water‐Based formulation allows for easier application and clean‐up RECOMMENDED USES H&C® ACRYLA‐DECK™ with COOL FEEL™ TECHNOLOGY is formulated for use on properly prepared interior or exterior concrete including pool decks, concrete patios and walkways, lanais and covered porches, athletic courts, block and stucco walls and interior concrete floors, basement and laundry room floors. COVERAGE RATES Substrate* sq ft/gal Concrete floors 200‐300 Porous concrete 150‐250 Concrete block 100‐150 *Coverage will vary depending on the porosity and texture of the substrate. JOBSITE TEST SECTION Due to the wide variety of substrates, preparation methods, application methods and environments, it is important to test the product in an inconspicuous spot for adhesion and compatibility prior to full‐scale application. H&C Products Group 101 W. Prospect Avenue Cleveland, Ohio 44115 WATER‐BASED SOLID COLOR HI‐BUILD DECK COATING WITH COOL FEEL™ TECHNOLOGY LIMITATIONS Do not apply if rain is expected within 12 hours following application. Do not use for immersion service, below grade substrates, or substrates constantly in contact with moisture. Do not use in highly corrosive or chemical environments or areas subject to intense heat. Reduction in surface temperature occurs only in exterior application. Do not use on wood surfaces. SURFACE PREPARATION New Concrete: Allow new concrete to cure at least 28 days. Concrete surfaces should be able to absorb water. To test absorption, spray various sections of the surface to be coated with water. If the water does not absorb rapidly, then acid etch the surface using H&C™ CONCRETEREADY™ Etching Solution, following label instructions. After proper etching, the surface should feel like 120‐grit sandpaper. If not, then etch again. Mechanical abrasion methods may be necessary to achieve proper profile. Do not apply the stain until all surfaces are porous. Allow all surfaces to dry at least 24 hours before staining. Prepared concrete must have a pH of 6 to 10. Existing and Previously Painted Concrete: Do not apply previously coated solvent based coatings. Can be applied over water based coatings that are properly cleaned and in good condition. All concrete must be porous, clean, dry and free of grease, oil and other contaminates. To spot clean, use H&C™ CONCRETEREADY™ Cleaner Degreaser, following label directions. If mold, mildew, or fungus is present, kill and remove with a solution of 1 cup household bleach to 1 gallon of water. If surface has been previously painted, remove all old, peeling, flaking paint by rough sanding to ensure adhesion of H&C®

APPLICATION INSTRUCTIONS Apply H&C® ACRYLA‐DECK™ with COOL FEEL™ TECHNOLOGY onto dry surfaces. Air, surface and material temperatures must be between 50° and 90° F. If surface temperatures exceed 90° F, reduce the temperature by dampening the surface with a fine spray of water. How to Apply: Apply with a brush or roller. Stir product thoroughly before and during application. When using more than one container, intermix all containers to ensure color uniformity. Prior to applying the first coat, dry sweep the concrete with a stiff bristle broom or shop vacuum to remove ...

LIMITED WARRANTY Seller’s and manufacturer’s only obligations shall be to replace such quantity of product proved to be defective. Neither seller nor manufacturer shall be liable for any injury, loss or damage, direct or consequential; arising from the applicator’s inability to use the product for his/her intended use. The user assumes all risk and liability. TECHNICAL SERVICES The information and recommendations set forth in this product data sheet are based on tests conducted by or on behalf of H&C® Products Group and The Sherwin‐Williams Company. ...