ECOSELECT ™ Zero VOC Interior Latex Flat
2Pages

Sherwin Williams. 101.85 EcoSelect™ Zero VOC Interior Latex characteristics EcoSelect Interior Latex Flat is a zero VOC, economical, interior latex flat wall paint for use on walls and ceilings of wallboard, primed plaster, wood, and masonry. Color: Extra White To optimize hide and color development, always use the recommended P-Shade primer Coverage: 350 - 400 sq ft/gal @ 4.0 mils wet; 1.1 mils dry Drying Time, @ 77°F, 50% RH: Touch: 1 hour Drying and recoat times are temperature, humidity, and film thickness dependent Flash Point: N/A Tinting with CCE: Base oz/gal Strength Vehicle Type: Vinyl Acrylic A21W01851 Voc (less exempt solvents): <50 g/L; <0.42 lb/gal As per 40 CFR 59.406 and SOR/2009-264, s.12 Volume Solids: 27 ± 2% specifications Block 1 ct. PrepRite Block Filler or Loxon Block Surfacer 2 cts. EcoSelect Interior Latex Drywall Self-prime using 2 cts. of EcoSelect Interior Latex Flat, or 1 ct. ProMar 400 Zero VOC Primer 2 cts. EcoSelect Interior Latex Masonry 1 ct. Loxon Concrete & Masonry Primer 2 cts. EcoSelect Interior Latex Plaster 1 ct. Premium Wall & Wood Primer 2 cts. EcoSelect Interior Latex Wood 1 ct. Premium Wall & Wood Primer 2 cts. EcoSelect Interior Latex Other primers may be appropriate. When repainting involves a drastic color change, a coat of primer will improve the hiding performance of the topcoat color. surface preparation WARNING! Removal of old paint by sanding, scraping or other means may generate dust or fumes that contain lead. Exposure to lead dust or fumes may cause brain damage or other adverse health effects, especially in children or pregnant women. Controlling exposure to lead or other hazardous substances requires the use of proper protective equipment, such as a properly fitted respirator (NIOSH approved) and proper containment and cleanup. For more information, call the National Lead Information Center at 1-800-424-LEAD (in US) or contact your local health authority. Remove all surface contamination by washing with an appropriate cleaner, rinse thoroughly and allow to dry. Existing peeled or checked paint should be scraped and sanded to a sound surface. Glossy surfaces should be sanded dull. Stains from water, smoke, ink, pencil, grease, etc. should be sealed with the appropriate primer/sealer. Recognize that any surface preparation short of total removal of the old coating may compromise the service length of the system. Anti-Microbial This coating contains agents which inhibit the growth of mold & mildew on the surface of this coating film. Drywall Fill cracks and holes with patching paste/ spackle and sand smooth. Joint compounds must be cured and sanded smooth. Remove all sanding dust. Masonry, concrete, cement, Block All new surfaces must be cured according to the supplier's recommendations— usually about 30 days. Remove all form release and curing agents. Rough surfaces can be filled to provide a smooth surface. If painting cannot wait 30 days, allow the surface to cure 7 days and prime the surface with Loxon Concrete & Masonry Primer.

Sherwin Williams. EcoSelect™ Zero VOC Interior Latex Flat A21 Series cleanup information Clean spills, spatters, hands and tools immediately after use with soap and warm water. After cleaning, flush spray equipment with compliant cleanup solvent to prevent rusting of the equipment. Follow manufacturer's safety recommendations when using solvents. surface preparation Plaster Bare plaster must be cured and hard. Textured, soft, porous, or powdery plaster should be treated with a solution of 1 pint household vinegar to 1 gallon of water. Repeat until the surface is hard, rinse with clear water...