SGM SAFETY INFORMATION
1 / 8Pages

Catalog excerpts

SGM SAFETY  INFORMATION - 1

© 2018 SGM Light A/S®. English edition. The information in this document is subject to change without notice. SGM and all affiliated companies disclaim liability for any injury, damage, direct or indirect loss, consequential or economic loss, or any other loss occasioned by the use of, inability to use, or reliance on the information contained in this document or in the user manual. The user manual may be downloaded from www.sgmlight.com. The SGM logo, the SGM name, and all other trademarks in this document pertaining to SGM services or SGM products are trademarks owned or licensed by SGM, its affiliates, and subsidiaries. Revision B

Open the catalog to page 1
SGM SAFETY  INFORMATION - 2

READ CAREFULLY! Review the following safety precautions carefully before installing or operating the device. SGM luminaries are not suitable for household use. They are intended for professional use only. Les luminaires SGM sont impropre à l’usage domestique. Uniquement à usage professionnel. DANGER! Risk of electric shock. Do not open the device. • • • • • Do not open the device; there are no user-serviceable parts inside. Ensure that power is cut off when wiring the device to the AC mains supply. Ensure that the device is electrically connected to earth (ground). Do not apply power if the...

Open the catalog to page 2
SGM SAFETY  INFORMATION - 3

• Do not put the battery in fire, attempt to heat it, or use it in a high temperature environment. • Do not install the battery backwards with reversed polarity. • Do not connect the positive terminal to the negative terminal of the battery with any metal object (such as a wire). • Do not carry or store the battery together with necklaces, hairpins, or other metal objects. • Do not pierce the battery with nails, strike the battery with a hammer, step on the battery, or otherwise subject it to strong impacts or shocks. • Do not expose the battery to water or salt...

Open the catalog to page 3
SGM SAFETY  INFORMATION - 4

Figure 1: Connecting AC Power Quick Installation Guide This leaflet is merely a quick installation guide for SGM moving head and SGM stationary lights, containing important safety information. For detailed information, please always consult the user manual of the product, available for download at www.sgmlight.com. Unpacking Unpack the device and inspect it to ensure that it has not been damaged during transport. Connecting AC power Please check the product label of the fixture to get the correct voltage range. Connect the fixture to AC power by mounting a power connector to the bare ended...

Open the catalog to page 4
SGM SAFETY  INFORMATION - 5

Connecting to a DMX control device The fixture is controllable using a DMX control device, and it can be connected using either a DMX cable or via the fixture’s built-in CRMX wireless receiver system, if included. When using a cabled DMX system, connect the DMX-In cable to the input connector and DMX-Out cable to the output, both located on the rear of the fixture’s base (male and female 5-pin XLR plugs). For outdoor events, use at least IP65-rated XLR connectors. Remember to terminate the DMX-Out cable of the last fixture in the data link. If using a wireless DMX system, remember to...

Open the catalog to page 5
SGM SAFETY  INFORMATION - 6

POI Quick Installation Guide Connecting DMX and AC power DMX in and DMX out are in the same cable. See more about the SGM POI DMX Cable in the picture on the right. Power is wired as the standard version. See “Connecting AC power” on page 4. For permanent installations, have a qualified electrician to wire the mains cable directly to a suitable branch circuit. POI products must always be powered on, so dehumidifiers perform properly. The junction’s ingress protection (IP) rating must be suitable for the location. For a temporary installation, the mains cable may be fitted with a grounded...

Open the catalog to page 6
SGM SAFETY  INFORMATION - 7

POI Spanner All the static POI products include a spanner with magnet, whose function is to establish connection between the fixture and the wireless transmitter. The spanner also has two types of pig-nose keys used for tilt adjustment in POI fixtures. Depending on type of fixture, it is used either the large or the small pig-nose keys. Connecting a wireless transmitter to a POI fixture A: Magnet B: Pignose for tilt lock - small C: Pignose for tilt lock - large Figure 4: POI Spanner In POI versions with wireless mode it is necessary to pair the fixture with a new transmitter (by default the...

Open the catalog to page 7
SGM SAFETY  INFORMATION - 8

Support hotline SGM offers 24/7 technical support hotline. Worldwide: +45 3840 3840 US: +1 877 225-3882 support@sgmlight.com SGM Light A/S Sommervej 23 8210 Aarhus V Denmark Tel: +45 70 20 74 00 info@sgmlight.com www.sgmlight.com

Open the catalog to page 8

All SGM Light catalogs and technical brochures

  1. i·5 UV POI

    6 Pages

  2. Q·7 W POI

    6 Pages

  3. Q-SERIES

    26 Pages

  4. P-SERIES

    24 Pages

  5. I-SERIES

    24 Pages

Archived catalogs

  1. P-5

    44 Pages

  2. PILOT 3000

    116 Pages