5000 DUOTHERM SERIES CASEMENT WINDOWS AND HINGE DOORS WITH THERMAL BREAK
36Pages

5000 DUOTHERM SERIES CASEMENT WINDOWS AND HINGE DOORS WITH THERMAL BREAK Fixed frame and opening profiles must be composed of two independent modules that are linked together by insulating clips in polyamide 6.6. To ensure that the profiles offer sufficient support and rigidity, they must be at least 52mm thick for the fixed frame, and between 52mm and 62mm thick for the opening. For a perfect waterproofness, doors must be fitted with 3 gaskets between the fixed frame and the opening: - a classic overlap gasket positioned outside (uncut, turning in corners); - a classic overlap gasket positioned inside (uncut, turning in corners) - a central gasket positioned along the median axis (with vulcanised corners). All of these gaskets are compressed when the active leaf is closed. The zone created between the outside gasket and the central gasket constitutes a decompression chamber that forces seepage out through drainage slots protected by deflectors with anti-backflow valves. MANUFACTURING PROCESS Profiles are mitre-joint assembled. Aluminium alloy corner cleats are inserted into the tubing. The manufacturer can choose to fix corner cleats by crimping, cottering or using studs. Whatever the system, open ends must be tightened automatically. Corner cleats are either glued into position with a two-component epoxy adhesive then sealed with a liquid mastic containing acrylic polymers (such as Microgutta or Smalljoint), or bonded into place using a category 1 elastomer polyurethane mastic (such as Ordoflex 42). GLAZING The glazing is 36mm thick at most. It is either maintained by clip-on glazing bead or "pocket" assembled, as the manufacturer prefers (in the latter case, however, and in the absence of spacers, jacks must be used to ensure active leaves can be squared). The waterproofing gaskets between the aluminium frame and the glazing are in EPDM (ethylene propylene diene monomer). FITTING Elements will be fitted in compliance with the architect's plans, either: Construction: by fitting special profiles to the fixed frame to adapt it to the thickness of the insulation (jambs, top and bottom cross rails), and adding cover strips for the interior finish (selection of dimensions and styles); Renovation: by incorporating jacks into the fixed frame to facilitate fitting and adjusting; external cladding on request; cover strips for interior finish (selection of dimensions and styles). 5000 DUOTHERM SERIES CASEMENT WINDOWS AND HINGE DOORS WITH THERMAL BREAK

5000 DUOTHERM SERIES CASEMENT DOORS AND HINGE DOORS WITH THERMAL BREAK FIXED FRAME AIR/WATER/WIND TESTS THERMAL PERFORMANCES Duotherm range carries certificate n°174-12-24 dated 15/12/2004 with glazing Ug=1.1 Warm Edge Dimensions < 2.3m2 Uw = 1.2W/m2.K Sw : 0,48 Tlw : 0,65 avec triple vitrage Ug=0.9 Warm Edge Dimensions < 2.3m2 FIXED FRAME 5000 DUOTHERM SERIES CASEMENT DOORS AND HINGE DOORS WITH THERMAL BREAK

5000 DUOTHERM SERIES CASEMENT DOORS AND HINGE DOORS WITH THERMAL BREAK FIXED FRAME THERMAL INSULATION On the outside, surfaces must be flat and as discreet as possible. For the inside, the architect can select between different styles of glazing bead, such as moulded, rounded, or simply straight at a sharp angle. The maximum dimension of peripheral aluminium around the panes is 38mm. Thermal insulation between outside and inside profiles is provided by clips in fibreglass-reinforced polyamide 6.6. Together with the selected glazing, this guarantees that applicable thermal regulations are...

5000 DUOTHERM SERIES CASEMENT DOORS AND HINGE DOORS WITH THERMAL BREAK INWARD-OPENING CASEMENTS, 1 OR 2 LEAVES AIR/WATER/WIND TESTS THERMAL PERFORMANCES ACOUSTIC TESTS Duotherm range carries certificate n°174-12-24 dated 15/12/2004 *avec with douple glazing Ug=1.1 Warm Edge *with triple glazing Ug=1.10.8 Warm Edge RA.tr = 40.4 dB(A) (1 leaf 1230x1480/ contrasonor 40) MAXIMUM DIMENSIONS: 1 LEAF W=1200MM H=2400MM, 2 LEAVES W=2400MM H=2400MM MAXIMUM WEIGHT PER LEAF: 100 kg INWARD-OPENING CASEMENTS, 1 OR 2 LEAVES 5000 DUOTHERM SERIES CASEMENT DOORS AND HINGE DOORS WITH THERMAL BREAK

5000 DUOTHERM SERIES CASEMENT DOORS AND HINGE DOORS WITH THERMAL BREAK INWARD-OPENING CASEMENTS, 1 OR 2 LEAVES APPEARANCE On the outside, surfaces must either be flat or slightly curved with opening and fixed frame unaligned in such a way as to create an effect of relief. This breaks the monotony of the series of aluminium surfaces on show. Inside and for the same reasons, the opening should under no circumstances be aligned to the fixed frame. Furthermore, the architect will want to choose between different styles of glazing bead, such as moulded, rounded or simply straight at a sharp...

5000 DUOTHERM SERIES CASEMENT DOORS AND HINGE DOORS WITH THERMAL BREAK INWARD-OPENING CASEMENTS, 1 OR 2 LEAVES VERTICAL CROSS-SECTION NEW CONSTRUCTION Cross-section scale: 1/3 STRAIGHT FRAME AND LEAF VERSION HORIZONTAL CROSS-SECTION DIFFERENT TYPES OF COVER STRIP (CREATION AND RENOVATION)

5000 DUOTHERM SERIES CASEMENT DOORS AND HINGE DOORS WITH THERMAL BREAK INWARD-OPENING CASEMENTS, 1 OR 2 LEAVES RENOVATION CURVED FRAME AND LEAF VERSION Cross-section scale: 1/3 VERTICAL CROSS-SECTION CROSS RAILS (CREATION AND RENOVATION) HORIZONTAL CROSS-SECTION

5000 DUOTHERM SERIES CASEMENT DOORS AND HINGE DOORS WITH THERMAL BREAK HINGE DOORS WITH LOCK, 1 OR 2 LEAVES AIR/WATER/WIND TESTS THERMAL PERFORMANCES Duotherm range carries certificate n°174-12-24 dated 15/12/2004 *with douple glazing Ug=1.1 Warm Edge *Dimensions >2,3m2 *avec with triple glazing Ug=0.8 Warm Edge *Dimensions >2,3m2 MAXIMUM DIMENSIONS: 1 LEAF W=1200MM H=2400MM, 2 LEAVES W=2400MM H=2400MM MAXIMUM WEIGHT PER LEAF: 100 kg HINGE DOORS WITH LOCK, 1 OR 2 LEAVES 5000 DUOTHERM SERIES CASEMENT DOORS AND HINGE DOORS WITH THERMAL BREAK

5000 DUOTHERM SERIES CASEMENT DOORS AND HINGE DOORS WITH THERMAL BREAK HINGE DOORS WITH LOCK, 1 OR 2 LEAVES APPEARANCE On the outside, surfaces must either be flat with opening and fixed frame unaligned in such a way as to create an effect of relief. This breaks the monotony of the series of aluminium surfaces on show. Inside and for the same reasons, the opening should under no circumstances be aligned to the fixed frame. Furthermore, the architect will want to choose between different styles of glazing bead, such as moulded, rounded or simply straight at a sharp angle. Maximum dimensions...