Crossbeam section 60 x 80mm minimum. Main direction of rain Minimum overlap: 1 corrugation Cap seal with screw Cap seal with screw Corrugation strut Crossbeam Fix the edge of the sheets at the gutter every two corrugations Remove the surplus with shears or a fine-toothed saw blade. ACCESSORIES Plaquette Cale d'ondes MAINTENANCE Cleaning possible using pressure pump, at reduced pressure with cold water. TECHNICAL PROPERTIES PROPERTIES PHYSICAL PROPERTIES MECHANICAL PROPERTIES THERMAL PROPERTIES OPTICAL PROPERTIES Density Water absorption Flexural strength Tensile strength Percentage elongation at break Modulus of elasticity in flexion Modulus of rupture in traction Operating temperature Coefficient of thermal conductivity Heat distortion temperature Heat transfer Linear thermal expansion Light transmission As a result of constant technological developments, the information and presentations contained in the present booklet are given only as an indication and without commitment on our part. SEDPA is committed to providing free-of-charge the replacement of goods which have broken during the guarantee period under the following conditions: - the conditions of installation and recommendations stated previously have been followed, as in our technical notes. - the exclusive use in traditional roofing and cladding applications - the return of a copy of proof of payment in the 15 days following the purchase. The manufacturer, not having control over the use of the material by others, cannot therefore guarantee the same results as those described in this document. Each user must carry out his own tests to determine up to what point the material corresponds to his needs. The manufacturer and his distributors cannot be held responsible for damage arising from a defective installation of the material. SEDPA France SA - Zone du Bois - BP 9 - 59840 PERENCHIES - FRANCE Tel. 0033.320.00.99.00 - Fax. 0033.320.00.99.29 - E-mail : [email protected] Corrugated and flat polyester resin sheets and rolls For installing the sheets, use rust-proof fasteners spaced regularly every three or four corrugations. Moderately tighten the fasteners after the fixing attachments have been installed. Check the effectiveness the seal ring by leaving the sheets to expand freely. Intermediate crossbeam Lay the sheets across the roof crossbeams with an overlap of one or two corrugations. FIBROLUX FIBROLUX Cut the FIBROLUX sheets to the required length using shears or with a fine-toothed saw blade. Translucent Reinforced with glass fibre Shock resi

Large corrugations 177/51 CLEAR Width : 920 mm Length : 1250 mm - 1520 mm 1750 mm - 2000 mm - 2500 mm 3000 mm - 6000 mm 177 mm Corrugated and flat polyester resin sheets and rolls FIBROLUX FIBROLUX SHEET PROFILES : Small corrugations 76/18 BLUE-YELLOW-GREEN Width : 900 mm Length : 2000 mm - 2500 mm 6000 mm FIBROLUX is a corrugated polyester reinforced with glass fibres. Its high shock and UV resistance guarantee its long life. CLEAR Width : 900 mm Length : 1520 mm - 2000 mm 2500 mm - 3000 mm - 6000 mm 76 mm With a good quality-price ratio, Fibrolux withstands temperature, variations, climate...

Large corrugations 177/51 CLEAR Width : 920 mm Length : 1250 mm - 1520 mm 1750 mm - 2000 mm - 2500 mm 3000 mm - 6000 mm 177 mm Corrugated and flat polyester resin sheets and rolls FIBROLUX FIBROLUX SHEET PROFILES : Small corrugations 76/18 BLUE-YELLOW-GREEN Width : 900 mm Length : 2000 mm - 2500 mm 6000 mm FIBROLUX is a corrugated polyester reinforced with glass fibres. Its high shock and UV resistance guarantee its long life. CLEAR Width : 900 mm Length : 1520 mm - 2000 mm 2500 mm - 3000 mm - 6000 mm 76 mm With a good quality-price ratio, Fibrolux withstands temperature, variations, climate...

INSTALLATION Cut the FIBROLUX sheets to the required length using shears or with a fine-toothed saw blade. RECOMMENDATIONS Lay the sheets across the roof crossbeams with an overlap of one or two corrugations. For installing the sheets, use rust-proof fasteners spaced regularly every three or four corrugations. Modemtely tighten the fasteners after the fixing attachments have been installed. Check the effectiveness the seal ring by leaving the sheets to expand freely. FIXING - Minimum overlap: 1 corrugation Corrugation strut Fix the edge of the sheets at the gutter every two corrugations Remove...