Because ceramic and stone tiles are inherently brittle, their exposed edges can chip and crack if left unprotected. Transitions between floor surfaces and at thresholds are particularly vulnerable to damage. Schluter-Systems offers a variety of profiles to provide edge protection and transitioning at thresholds and between adjacent surfaces, resulting in durable, maintenance-free tiled coverings. The profiles can be grouped into two categories: transitions between same-height surfaces and transitions between different-height surfaces Application and Function Same-height Transitions 1.1 Schluter®-SCHIENE is designed to provide edging for tile coverings. Typical applications include edge protection where tile is bordered by carpet, at expansion joints, or as a decorative edging for stairs. SCHIENE is available in stainless steel, solid brass, aluminum, and anodized aluminum. The profile features a trapezoid- perforated anchoring leg, which is secured in the mortar bond coat beneath the tile, and an 87° sloped vertical wall section that transfers point loads to the substrate and surface covering while protecting tile edges from damage. SCHIENE, in solid brass, aluminum, and anodized aluminum, features a 5° sloped top flange and fillet at the anchoring leg/vertical section interface to enhance edge protection by reducing stresses on the tile, and, in sizes greater than 1/4" (6 mm), features an integrated joint spacer that establishes a defined joint cavity between the tile and the profile. The anchoring leg of SCHIENE, in all materials, is available with a special radius perforation “R” so that the profile can be used to form curves. / / / / / // // // /s/s/ss 1.6 Schluter®-DECO is designed to provide decorative lines within tile coverings and edge protection at transitions from tile coverings to other same-height surface coverings, such as wood or carpet. The profile is available in stainless steel, solid brass, chrome-plated 1.7 Schluter®-RENO-V solid brass, and anodized aluminum. DECO features a trapezoid-perforated anchoring leg, which is secured in the mortar bond coat beneath the tile, and a 1/4" (6 mmj-wide visible surface that meets the high aesthetic requirements of showrooms, lobbies, galleries, exhibition booths, etc. The anchoring leg of DECO, in solid brass, chrome-plated solid brass, and anodized aluminum, is available with a special radius perforation “R” so that the profile can be used to form curves. DECO in chrome-plated brass requires a relatively large bending radius.

FLOOR PROFILES 1.3 Schluter®-RENO-T is designed to provide transitions between existing same-height, hard-surface floor coverings (e.g., ceramic tile or natural stone, parquet flooring, concrete pavers, laminate, etc.), primarily in retrofit applications. The profile is available in stainless steel, solid brass, and anodized aluminum. RENO-T is installed within the existing joint cavity and overlaps adjoining surface materials, thus preventing edges from becoming damaged when subjected to mechanical stress. RENO-T, in brass and anodized aluminum size 9/14, is flexible in the lateral direction...

FLOOR PROFILES the suitability of a proposed type of profile must be verified based on the anticipated chemical, mechanical, and/or other stresses. Exceptions and special considerations are listed below: Stainless steel profiles are roll-formed, resulting in a slightly different contour from those made of extruded brass or aluminum. Stainless steel can sustain high mechanical stresses and is particularly well suited for applications requiring resistance against chemicals and acids; for example in the food industry, breweries, dairies, commercial kitchens, and hospitals, as well as in residential...

FLOOR PROFILES floor covering, but rather up to approx. 1/32" (1 mm) lower. 4. Fill the joint completely with grout or setting material. 5. Work with materials and tools that will not scratch or damage sensitive surfaces. Setting materials must be removed immediately. RENO-T 1. Select the profile according to joint width, to ensure proper support of the lateral crosspiece. 2. The joint cavity must be at least 3/8" (9 mm) deep and free of debris. Substances that inhibit adhesion must be removed from the sides of the joint. 3. Fill the joint with elastomeric sealant such as Schluter®-KERDI-FIX...

R = Radius Notes: • Radius available for JOLLY in metal profiles only. • JOLLY in polished aluminum and chrome-plated brass require a relatively large bending radius. Note: Only the brass and aluminum DECO are available in radius.

FLOOR PROFILES 1.3 Schluter®-RENO-T Stainless steel Note: Only the brass and aluminum RENO-TK are available in radius (sizes 60 - 100).

Stainless steel, Brass ADA-Compliant Note: When leading edge abuts lower surface covering, sizes 3/4" (20 mm) and 11/16" (17.5 mm) are not ADA-compliant. When leading edge rests on top of lower surface covering, sizes 3/4" (20 mm), 9/16" (15 mm), and 11/16" (12.5 mm) are not ADA-compliant. Note: RENO-RAMP sizes 3/4" - 20 mm and 9/16" - 15 mm are not ADA-compliant.

FLOOR PROFILES 1.7 Schluter®-RENO-VT

Schluter® Systems Floor Profiles 5-Year Limited Warranty LIMITED WARRANTY COVERAGE: Subject to the conditions and limitations as stated in this Schluter® Systems Floor Profiles 5-Year Limited Warranty (the “Limited Warranty”), Schluter Systems warrants that its Schluter®-SCHIENE, Schluter®-JOLLY, Schluter®-RENO-TK, Schluter®-DECO, Schluter®-RENO-U, Schluter®-RENO-T, Schluter®RENO-RAMP, Schluter®-RENO-RAMP-K, and Schluter®-RENO-V (collectively, the “Products”) will be free from manufacturing defects and will perform as described in the Schluter Systems Floor Profiles Technical Data Sheet (collectively,...