09/11 - 2 Construction subject to change. Version: 27.03.2019 No return possible!

Smoke detection system RMS Description Industrial property rights owned by SCHAKO: - Patent: DE 199 51 403 A1 - Registered utility model: 20023533.8 - Patent: EP 122 4641 - VdS Approval: G209206 External monitoring is done by the VdS Schadensverhütung GmbH Köln (VdS Damage Prevention Branch, Cologne) The SCHAKO smoke detection system consists of the smoke detector RMSII-L and the relay module RM V4.00 and is used in places where, at the earliest possible stage of a fire (upon occurrence of cold smoke of < 72°), triggering and switching operations are to be controlled automatically. It can be...

Smoke detection system RMS Installation arrangement and mounting The smoke detector must be fitted free of vibration if possible. When charged with steam, disinfectant, dust, soot (exhaust gases) or dew, an alarm or fault message is triggered. Assembly in ducts 1. Establish smoke detector position (not in the inspection opening of the fire damper), and mark the middle. 2. Cut out a hole of 120 mm in diameter. 3. Drill mounting holes (only when installed on site in the ventilation duct). 4. Insert the delivered insulating sleeves into the mounting holes. 5. Fit smoke detector with mounting frame...

Smoke detection system RMS Construction Smoke detector base - Polycarbonate Connecting cable - 2.0 m with 9-pin Sub D plug. The 9-pin Sub D terminal for the electric supply and trigger lines is located inside the base. Individual display - LED on duct exterior Mounting frame - Sheet steel, with seal Accessories Assembly part type EBT - for installation flush with the duct, made of galvanised sheet steel. - Housing leakage according to DIN EN 1751, class B, at a duct pressure of up to 1000 Pa. Assembly part (-REBT / -REBTF) - for installation in round ducts, made of galvanised sheet steel. - Housing...

Smoke detection system RMS Accessories with assembly part (-EBT), for fire damper installation - Installation in duct topside - Installation in duct side wall The dimension L depends on the height H (mm). The smoke detector must always be assembled in the assembly part type EBT on the operator side (trigger device, drive) (not in the inspection opening of the fire damper). Construction subject to change.

Smoke detection system RMS with assembly part (-REBT), for installation in round ducts with assembly part (-REBTF), for installation in round ducts - without flange, with rubber lip seal. - with flange on both sides, to EN 12220. Available sizes REBT / REBTF 1.) painted black matt on the inside Construction subject to change.

Smoke detection system RMS Technical dataSmoke detection system (-RMS) Operating voltage: Connection assignment of the 9-pin SUB-D plug: The relays drop off when an alarm / a fault or a power cut occurs. 09/11 - 8 Version: 27.03.2019 Construction subject to change.

Smoke detection system RMSCircuit diagram of relay module 1.) Smoke detectors 10.) AMP plug for 24V AC/DC actuators (max. 10 VA) 11.) Selector switch 1, e.g., actuator 12.) Selector switch 2, e.g., light 13.) Contact load of the selector switches 14.) Spring return actuator 24 V AC/DC for fire damper. SCHAKO product or external product (for the technical data, please refer to the motor data sheet) 15.) Spring return actuator 24 V AC/DC / 230 V AC SCHAKO product or external product (optional) (for the technical data, please refer to the motor data sheet) 16.) Magnetic clamp / pneumatic valve (optional)...

Smoke detection system RMS Maintenance / Inspection Maintenance of the smoke detection device for fire and smoke dampers must be carried out once a year or after a fault message, due to contamination. Note Installation and wiring must be carried out by authorised electricians only. The agreed regulations of the technic, safety and accident prevention regulations as well as the VDE guidelines, regulations of the local EVU's and the wiring instructions and connection plans of the manufacturer, must be adhered to when installing, wiring and commissioning. When wiring the junction boxes, make sure...

Smoke detection system RMS Order details Specification texts Smoke detection system Type RMSΙΙ-L Accessories: Assembly part for duct installation -EBT Relay module -RM incl. RST Assembly part for duct connection without flange with rubber lip seal -REBT with flange, on both sides according to EN 12220 -REBTF Order example RMSΙΙ-L-RM Unless stated otherwise, the thick-frame model will be delivered! Smoke detection system type RMS, with annual maintenance, for installation flush with the duct or fire damper installation with assembly part type EBT (extra charge), with maintenance cover. Consisting...