BSG
1 / 19Pages

Catalog excerpts

01/15 - 2 Construction subject to change. Version: 26.09.2018 No return possible!

BaM-impact-Resistant Grilles BSG Fastening Screw mounting (-SM) - Standard, screws must be provided on site Description The ventilation grilles type BSG-N for supply and return air with facing horizontal fixed profiled rods are suitable for fitting into gymnasiums and sport halls, due to the fact that they are ball-impact-resistant to DIN 180 32 Part 3. When installed at a height of less than 2 m, the profile spacing must not exceed 8 mm. Please specify, when ordering. The ventilation grilles type BSG-S for supply and return air with facing vertical fixed profiled rods and pivoting...

Open the catalog to page 3

Ball-Impact-Resistant Grilles BSGModels and dimensionsDimensions BSG-N-...-SB-... BSG-N-...-AL-... Available sizes BSG-ST bined lengths and heights available! Construction subject to change.

Open the catalog to page 4

Ball-Impact-Resistant Grilles BSG BSG-S-...-SB-... bined lengths and heights available! Construction subject to change.

Open the catalog to page 5

Ball-Impact-Resistant Grilles BSGDimensions of accessories Plenum box (-AK) with lateral spigot (-S1) Grilles cannot be fitted with a hit-and-miss damper if a plenum box is attached, i.e., it can either be fitted with a hit-and-miss damper or a plenum box. Rubber lip seal (-GD1) Detail X Insulation for plenum box AK internal (-Ii) external (-Ia) Construction subject to change.

Open the catalog to page 6

Ball-Impact-Resistant Grilles BSG Installation frame without wall anchors (-ER1) Length L < 825 mm = 4 wall anchors (at an extra charge) Length L > 825 mm = 6 wall anchors (at an extra charge) Installation frame E1 made of electrolytic galvanised sheet steel. Installation frames are only delivered with wall anchors on special request (-ER2, at an extra charge). Technical data Pressure loss and noise level Front side velocity BSG for supply and return air Construction subject to change.

Open the catalog to page 7

Ball-Impact-Resistant Grilles BSG BSG-N (supply air) without hit-and-miss damper BSG-N (return air) without hit-and-miss damper BSG-N (supply air) with hit-and-miss damper BSG-N (return air) with hit-and-miss damper Correction factor Supply air Construction subject to change.

Open the catalog to page 8

Ball-Impact-Resistant Grilles BSG Front side velocity BSG-S, supply and return air BSG-S (supply air) without hit-and-miss damper BSG-S (supply air) with hit-and-miss damper Face area BSG-S Supply and return air

Open the catalog to page 9

Ball-Impact-Resistant Grilles BSG Maximum end velocity of jet BSG-N (supply air), without coanda effect H (mm) 325 225 Construction subject to change. No return possible!

Open the catalog to page 10

Ball-Impact-Resistant Grilles BSG BSG-S (supply air), without coanda effect BSG-S (supply air), with coanda effect 01/16 - 11 Construction subject to change. Version: 26.09.2018 No return possible!

Open the catalog to page 11

Ball-Impact-Resistant Grilles BSG Jet path BSG-N (supply air), without coanda effect Heating Cooling BSG-S (supply air), without coanda effect 01/16 - 12 Construction subject to change. Version: 26.09.2018 No return possible!

Open the catalog to page 12

Ball-Impact-Resistant Grilles BSG Critical throw BSG-N (supply air), with coanda effect BSG-S (supply air), with coanda effect 01/16 - 13 Construction subject to change. Version: 26.09.2018 No return possible!

Open the catalog to page 13

Ball-Impact-Resistant Grilles BSG Maximum penetration In heating mode BSG-N (supply air), without coanda effect BSG-S (supply air), without coanda effect 01/16 - 14 Construction subject to change. Version: 26.09.2018 No return possible!

Open the catalog to page 14

Ball-Impact-Resistant Grilles BSG Induction ratios and temperature ratios BSG-N (supply air), without coanda effect BSG-N (supply air), with coanda effect BSG-S (supply air), without coanda effect BSG-S (supply air), with coanda effect 01/16 - 15 Construction subject to change. Version: 26.09.2018 No return possible!

Open the catalog to page 15

Ball-Impact-Resistant Grilles BSG Minimum distances BSG, supply air without coanda effect Legend Vzu (m3/h) [l/s] VX (m3/h) [l/s] vmax (m/s) Vk (m/s) vstirn (m/s) Astirn (m2) x (m) y (m) xkr (m) yAlu (m) ykr Alu(m) P (kg/m3) Dpt (Pa) Lwa [dB(A)] Lwai [dB(A)] KF (-) DTo (K) Correction factor (for scattered air jet) BSG-S (supply air), with or without coanda effect Blade position Supply air volume Total air jet volume at point x Maximum end velocity of jet Duct velocity Intake velocity, blower stream velocity, outflow velocity, relative to Astirn Face area Horizontal throw Vertical throw...

Open the catalog to page 16

BaM-impact-Resistant Grilles BSG Order code BSG 01 All fields must be filled when ordering Sample BSG-N-0625-125-SB-9010-SN-ER0 Ventilation grille type BSG I with facing horizontal fixed profiled rods I length 625 mm I height 125 mm I sheet steel I painted to RAL 9010 I without hit-and-miss damper I without installation frame ORDER DETAILS 01 - Type BSG = Ventilation grille type BSG 07 - Hit-and-miss damper SN = Without hit-and-miss damper (standard) SS = With hit-and-miss damper 02 - Motel 08 - Installation frame N = With facing horizontal fixed profiled rods ER0 = Without installation...

Open the catalog to page 17

BaM-impact-Resistant Grilles BSG Order code AK 01 All fields must be filled when ordering Plenum box, rectangular design I suitable for diffuser type BSG I length 325 mm I height 125 mm I single length I with screw mounting I galvanised sheet steel I with damper I with rubber lip seal I without box insulation I standard height of box I standard width of box I standard spigot diameter I lateral spigot ORDER DETAILS 01 - Type AK = Plenum box, rectangular design 02 - Air diffuser 40 = For ball-impact-resistant grilles type BSG 03 - Length 00325 = Grille length 325 mm 00425 = Grille length 425...

Open the catalog to page 18

Ball-Impact-Resistant Grilles BSG Specification texts Ventilation grille type BSG-N for supply and return air, in ballimpact-resistant design to DIN 180 32, Part 3. Consisting of a frame with facing horizontal fixed profiled rods made of sheet steel painted to RAL 9010 (white). Fastening by means of screw mounting (-SM). Product: SCHAKO type BSG-N-...-SB-9010-... - Plenum box (-AK) made of electrolytically galvanised sheet steel (only possible without hit-and-miss damper) - With damper (-DK1) in plenum box, adjustable, for simple air volume regulation - Rubber lip seal (-GD1), made of...

Open the catalog to page 19