Air diffuser system Model AUDIX®-AW

04/08 - 2 Construction subject to change. Version: 27.03.2018 No return possible!

Air Diffuser System Model AUDIX®-AW Description Modern office buildings are often built without suspended ceilings. This opens up a saving potential regarding the floor heights. This means that the same building height can accommodate more floors. To provide the possibly cheapest office space creates conflicts with the demand for comfort. Therefore, to reduce the room temperatures, in some cases component cooling systems are used for the ground load cooling. According to the thermal isolation regulations, an air-conditioning installation is demanded for dense facades, to prevent building damage...

Air Diffuser System Model AUDIX®-AW Characteristics of each slot diffuser: AUDIX®-AW-...-DSX: The air outflow direction can also be adjusted even after installation of the diffuser. In doing so, the free cross-section always remains constant. Likewise, the pressure loss and noise level do not change. A subsequent adjustment of the air jet pattern to changed room conditions is possible. For adjustment, single blades must be taken out and put back turned into the required air direction. The stable air jet means that the diffuser is suitable for VAV systems. AUDIX®-AW-...-DSX-XXL-W: The air outflow...

Air Diffuser System Model AUDIX®-AW Model AUDIX®-AW-R - for installation in walls, with round connection pipe AUDIX®-AW-RE - for installation in walls, with rectangular connection pipe AUDIX®-AW-...-Z - only supply air AUDIX®-AW-...-A - only return air AUDIX®-AW-...-Z/A - for supply and return air AUDIX®-AW-...-DSX - with slot diffuser type DSX - 1- to 4-slot - with narrow frame profile (-P) or wide frame profile (PB) AUDIX®-AW-...-DSX-XXL-W - with slot diffuser type DSX-XXL-W - 1- to 2-slot - with narrow frame profile (-P) or wide frame profile (PB) AUDIX®-AW-...-DSC - with slot diffuser type...

1.) For wall thicknesses >100 mm, a box neck extension (up to max. 260 mm) is required. View A for supply or return air (-Z or -A) II II View B for supply or return air (-Z or -A) Wall opening in the length: L+5 WO = wall opening Construction subject to change.

Air Diffuser System Model AUDIX®-AW Diffuser models Detail X AUDIX®-AW-DSX-P, 1 to 4 slots Construction subject to change. Version: 27.03.2018 No return possibl

Air Diffuser System Model AUDIX®-AW AUDIX®-AW-DSC, 1 and 2 slots Construction subject to change. Version: 27.03.2018 No return possibl

Air Diffuser System Model AUDIX®-AW Dimensions of accessories Damper (-DK), with cable adjustment AUDIX®-AW-R Box neck extension (-KHV) AUDIX®-AW-R-KHV AUDIX®-AW-RE-KHV AUDIX®-AW-RE Cover (-ÖA) To prevent contamination or damage during assembly. Rubber lip seal (-GD) (only AUDIX®-AW-R) Detail W 04/08 - 9 Construction subject to change. Version: 27.03.2018 No return possi

Air Diffuser System Model AUDIX®-AW Fastening methods Prong fastening (-BK, for AUDIX®-AW...-DSX / -DSX-XXL) The prong fastening (-BK) is always attached to the front (to the end pieces). Spring connection (-FM) for AUDIX®-...-DSC /-DSA) ® AUDIX -AW-...-DSC Installation Optimum installation The clearance between ceiling and upper edge of the diffuser must not exceed 0.5 m, otherwise no coanda effect is achieved! Installation of plenum box rotated AUDIX®-AW-R AUDIX -AW-...-DSA The spring connection (FM) is always attached to the diffuser on the longitudinal side. On request, the plenum box can...

Air Diffuser System Model AUDIX®-AW Technical data Maximum end velocity of jet AUDIX®-AW-DSX-...-1/2/3/4 Correction factors for maximum end velocity of jet DSX

AUDIX®-AW-DSA-D-1 Construction subject to change. Correction factors for maximum end velocity of jet DSC Correction factors for maximum end velocity of jet DSA-D Slot lengths

Air Diffuser System Model AUDIX®-AW AUDIX®-AW-DSA-VD-1 Correction factors for maximum end velocity of jet DSA-VD k factor Slot lengths 1200 mm 1000 mm 900 mm 800 mm 700 mm 600 mm 500 mm 400 mm DSA-VD positioned upwards x 0.87 x 1.00 x 1.07 x 1.14 x 1.28 x 1.42 x 1.55 x 1.66 DSA-VD positioned straight x 0.94 x 1.09 x 1.22 x 1.34 x 1.45 x 1.56 x 1.74 x 1.88 Maximum assembly dimension to achieve a coanda effect Nozzles positioned upwards Nozzles positioned straight 04/08 - 13 Construction subject to change. Version: 27.03.2018 No return possible!

Correction factors for x-critical DSX AUDIX -AW-DSX-XXL-W-1/2 Correction factors for x-critical DSX-XXL-W Construction subject to change. Slot lengths

Construction subject to change. Correction factors for x-critical DSC

AUDIX -AW-DSA-VD-1 Correction factors for x-critical DSA-VD

Construction subject to change. Correction factors for temperature ratio DSX-XXL-W

Correction factors for induction ratio DSA-VD Supply air volume Supply air volume Supply air volume per metre of slot Supply air volume per metre of slot Supply air volume per metre of row Supply air volume per metre of row total air jet volume at point x total air jet volume at point x Horizontal and vertical throw Temperature difference between supply air temperature and room temperature (aTq = tZU -tR) Temperature difference at point x Supply air temperature Room temperature Maximum end velocity of jet Induction ratio (i = Vx / Vzu) Temperature ratio (TV = ATx / ATq ) Critical throw Transmission...

Air Diffuser System Model AUDIX®-AW Ordering details Cross-talk sound attenuator Model AUDIX®-AW with round connection pipe -R with rectangular connection pipe -RE with slot diffuser with nozzles fixed with nozzles adjustable 1 row with special frame profile with standard frame profile with wide frame profile with narrow frame profile with wide frame profile with narrow frame profile with prong fastening -BK with spring connection -FM Rubber lip seal -GD (only AUDIX®-AW-R) Box neck extension -KHV Wall thickness >100 mm to max. 260 mm Order example: AUDIX®-AW-RE-Z-500-DSC 402 Unless stated otherwise,...