SINTOLIN SATINATO
2Pages

SINTOLIN SATINATO UNIVERSAL RUST-INHIBITING ALKYD SATIN ENAMEL series 923 DESCRIPTION Satin enamel, with alkyd-resin base, for wood and metal. New formulation with corrosion-inhibiting pigments, can be used as a sole primer and finisher on iron. Optimized drying and ease of application. For interiors and exteriors, it contains pigments stable in contact with the light and creates an effective protective barrier against atmospheric agents. shine of the metal must receive their base coat of rust inhibiting paint after no more than 8 hours. - Apply 2 coats of SINTOLIN SATINATO. New woodwork: - Dry sand in order to remove raised fibres; - Clean the surface, remove any material resulting from the woodworking along with any resin using suitable thinner; - Make sure the wood is not too damp; - On soft and dry wood, or excessively absorbent wood, apply a coat of MARCONOL IMPREGNANTE 843 and rub down lightly with abrasive paper. - In order to assure the finish has better filling power, apply 1-2 coats of MARCONOL ORIENTALITE primer 1450519 and sand. - Apply 2 coats of SINTOLIN SATINATO. - Type of Binder: alkyd resins - Solvent: mix of aliphatic hydrocarbons: - Specific gravity per UNI EN ISO 2811-1: 1.05-1.20 kg/l. (depending on the colour). - Viscosity per UNI 8902: 700 ± 100 cps (with Rotothinner rotational viscometer, at 25 C). - Gloss per UNI EN ISO 2813: 30-40 GU at 60° - Drying (25 °C and 65% R.H.): dust free in 2 hours; to touch in 5 hours; to recoat after 16 hours. Varnished woodwork: - Check the state of repair of any old coats of varnish, remove any parts which are flaking or not perfectly adherent. - Level any unevenness on the surface. Holes, cracks and defects can be treated using TAMSTUCCO PASTA 9400006 for interior woodwork. - Sand and clean. - In order to assure the finish has better filling power, apply 1-2 coats of MARCONOL ORIENTALITE primer 1450519 and sand. - Apply 2 coats of SINTOLIN SATINATO. INSTRUCTIONS FOR USE Can be applied onto: - Iron - Wood - Alloy steel, galvanized sheet metal, plastic-PVC when properly prepared. TECHNICAL SPECIFICATIONS PREPARING THE SURFACE Ferrous metalwork never previously painted: - Remove any compact and adherent calamine and all traces of rust by means of commercial-type sandblasting (Grade SA2), or clean mechanically or manually. In order to remove rust from awkward areas, use the RUGISTOP converter 5900100. - In the case of new surfaces which do not feature calamine or rust, simply remove any grease from the surface using cleaning thinner. - Dust the surface, make sure the background is completely dry and apply 2 coats of SINTOLIN SATINATO. - For exteriors in harsh environments on exposed surfaces, we recommended applying 2 coats of rust-inhibiting SATURNO series 191. After at least 16 hours, apply 2 coats of SINTOLIN SATINATO. Painted ferrous metalwork: - Remove any layers of old flaking paint and any rust by means of mechanical or manual cleaning, rub down in order to coarsen any old paint which is still perfectly adherent. In order to remove rust from awkward areas, use the RUGISTOP converter 5900100. - Remove dust from the surface. - Apply 2 coats of SINTOLIN LUCIDO. - In the case of considerably deteriorated surfaces, it is advisable to remove any old paint and rust completely by means of grade SA2 1/2 sandblasting, or using the SVERNICIATORE SM10 paint remover cod. 5610014 followed by careful mechanical or manual cleaning. - Any surfaces sandblasted down to reveal the original Galvanized aluminium or light alloys: - Remove all traces of oxide by means of mechanical or manual cleaning. - Carefully remove any grease using suitable alkaline solutions or thinner. - Remove all traces of dust and proceed with the application of PRIMER all-purpose anticorrosive primer cod. 1630307 on a perfectly dry surface. - Apply 2 coats of SINTOLIN SATINATO. Plastic surfaces (PVC): - Sand the surface to coarsen it slightly. - Degrease with a suitable diluent and clean the surface. - Apply a coat of the universal PRIMER 1630307. - After at least 12 hours and on perfectly clean and dry surface, apply 2 coats of SINTOLIN SATINATO. On plastic materials other than PVC, verify adhesion to determine compliance with the practice tests on the specific surface. APPLICATION INSTRUCTIONS Air and surface conditions: Air temperature: Min. +5 C / Max.+35 C. Relative humidity of the air: <80%. Temperature of the surface: Min. +5 C / Max. +35 C. Dry surface - Avoid applying the product when there is condensation on the surface, or in direct sunlight. - Tools: brush, short-wool roller, spray. - Carefully stir the product before dilution. - Thinner: White spirit 5200010 or Synthetic thinner 5210011. San Marco Group Spa - Via Alta 10 - 30020 Marcon (VE) - Tel +39 041 4569322 - www.san-marco.com - info@san-marco.it - export@san-marco.it

SAN MARCO GROUP guarantees that the information herein is provided to the best of its technical and scientific knowledge and based on its experience; nonetheless, the company may not be held liable for the results obtained using these products, as application conditions are beyond its control. It is recommended to always make sure that the product is suited to each specific instance. The present sheet voids and replaces any previously existing sheets. For further technical information call the technical service +39 041 4569322. San Marco Group Spa - Via Alta 10 - 30020 Marcon (VE) - Tel +39...