RonaDeck Resin Bonded Surfacing Rapid cure decorative slip resistant safety surfacing and landscaping FEATURES rapid cure resin can be trafficked after 4 hours high slip resistance DDA compliant self priming on asphalt and concrete highly decorative suitable for pedestrian and vehicular traffic available in a wide range of colours RonaDeck Resin Bonded Surfacing is a resin bonded aggregate surfacing system for paths, car parks, drives, ramps, highways etc. RonaDeck Resin Bonded Surfacing produces a surface with the appearance of natural aggregate or stone but with aggregate which is firmly bonded to the surface. It is designed for use on concrete, asphalt, steel and timber surfaces which require the application of a resin bonded aggregate, to provide some or all of the following: Decoration High friction surfacing Colour coding Compliance with Disability Discrimination Act Minimal maintenance An alternative to loose aggregate and stone surfacing RonaDeck Resin Bonded Surfacing provides surfaces for all types of traffic from paths to busy highways and provides excellent traction in wet and dry conditions. It has good adhesion to suitably prepared substrates, high abrasion and slip resistance values. Coloured or contrasting aggregates provide clear markings for safety and hazard areas. Natural aggregates are ideal for landscaping, driveways, paths, garden areas, car parks. Landscaping, gardens, driveways, footpaths Slip resistant surfacing on platforms, footbridges Balconies, common walkways Steps, car parks and ramps Marinas, jetties, sea walls, pond and lake surrounds Approaches to pedestrian crossings, junctions and other hazards Resin Bound and Bonded Surfacing Continued on following page... Other Ranges—Concrete Repair and Coatings, Screeds, Waterproofing and Tanking, and, Flooring and Bedding

RonaDeck Resin Bonded Surfacing Rapid cure decorative slip resistant safety surfacing and landscaping Technical Data Hardness Elongation Tensile Strength Adhesive Strength RonaDeck Resin Bonded GP Primer RonaDeck Resin Bonded Steel Primer RonaDeck Resin Bonded Surfacing Resin RonaDeck Resin Bonded Surfacing Aggregate RonaDeck Resin Bonded Seal Coat UV Coverage Rates (0.9—1.4mm aggregate) RonaDeck Resin Bonded GP Primer RonaDeck Resin Bonded Steel Primer RonaDeck Resin Bonded Surfacing Resin RonaDeck Resin Bonded Aggregate RonaDeck Resin Bonded Seal Coat (1st coat) RonaDeck Resin Bonded Seal Coat...

RonaDeck Resin Bonded Surfacing Rapid cure decorative slip resistant safety surfacing and landscaping Substrate Suitability (continued) RonaDeck Resin Bonded Surfacing is a specialist product and must only be applied by specialist applicators. If you are unsure of the suitability of a substrate for application of RonaDeck Resin Bonded Surfacing, do not proceed. RonaDeck Resin Bonded Surfacing is a thin layer of 1mm to 4mm (approximately) depending on the system. It will therefore reflect any substrate imperfections. Uneven substrates should therefore be levelled before application of RonaDeck...

RonaDeck Resin Bonded Surfacing Rapid cure decorative slip resistant safety surfacing and landscaping Instructions for Use Concrete should have a maximum relative humidity of 75% before RonaDeck Resin Bonded Surfacing is applied. Allow asphalt or asphalt concrete (macadam) to cure for at least 2-3 weeks, to ensure that free volatiles have evaporated. RonaDeck Resin Bonded Surfacing is not suitable for application to asphalt or asphalt concrete containing softer grades of bitumen. The bitumen binder must have a pen value no greater than 90 and preferably 40/60, when tested in accordance with EN...

RonaDeck Resin Bonded Surfacing Rapid cure decorative slip resistant safety surfacing and landscaping Instructions for Use (continued) Mix RonaDeck Resin Bonded Surfacing with a slow speed drill and spiral paddle, until the components are blended and the mix is free from streaks; immediately pour the mixed material onto the substrate, to prevent heating in the mixing vessel and to extend workable life. Spread the resin with a notched squeegee or roller at the rate of 1.5kg/m 2 for application of 1-3mm aggregate or 1kg/ m 2 for 0.9-1.4mm aggregate. Maximum application temperature is 35oC. Maximum...

RonaDeck Resin Bonded Surfacing Rapid cure decorative slip resistant safety surfacing and landscaping Aggregate Colour and Shading The sourcing and processing of the natural and pigmented aggregates supplied with RonaDeck Resin Bonded Surfacing cannot eliminate variability in their colour, shading and grading even though strict quality control measures are in place. We are therefore unable to guarantee that aggregates will be free from such variation and cannot accept any liability for any variation. Note that coloured aggregates are colour coated and will fade under UV light. Wear Resistance...

RonaDeck Resin Bonded Surfacing Rapid cure decorative slip resistant safety surfacing and landscaping Natural Aggregates Autumn Quartz 1-3mm Chinese Bauxite 0.9-1.4mm Chinese Bauxite 1-3mm Guyanan Bauxite 0.9-1.4mm Guyanan Bauxite 1-3mm Mufti Hint 1-3mm Red Granite 1-3mm Rounded Sepia 1-3mm Pigmented Aggregates The information detailed in this leaflet is liable to modification from time to time in the light of experience and of normal product application, and before using, customers are advised to check with Ronacrete Ltd, quoting the reference number, that they possess the latest issue. Any...