x cook
21Pages

{{requestButtons}}

Catalog excerpts

x cook - 6

6 CONTENTS Drawing explanation 6 Technical Specification 7 Packaging 7 Parts overview 7 1. IMPORTANT INFORMATION General warning and safety instructions 8 Before setting up 8 – 9 2. BRIEF HEATING INFORMATION Suitable fuels and fuel quantities 10 Maximum fuel quantity 10 Fuel quantities 10 Clean burning 11 Burning wood 11 3. INSTALLING THE FIRE Connecting the fire 12 4. OPERATION Lighting the fire 13 Ash drawer 14 Operating the shaker grate 14 Slide setting at rated heating capacity 14 5. FITTING OPTIONS Making an external combustion air feed 15 6. MAINTENANCE AND CLEANING General...

Open the catalog to page 6
x cook - 7

7 TECHNICAL SPECIFICATION (Illustrated: Fitting dimensions) This is a Design 1 fire and has a connection for fitting to a chimney that is equipped for other fires and boilers for solid and liquid fuels, insofar as the chimney dimensions are in accordance with DIN 4705, Part 3 Flue gas values for multiple connection to a chimney as per DIN 4705,Part 3 or for measuring the chimney as per DIN 4705, Part 2 Flue gas mass flow g/s 5,7 Flue gas temperature / °C 226,6° Minimum flow pressure at rated heating capacity 12 The owner of the small heating system or the authorised person for the small...

Open the catalog to page 7
x cook - 8

8 1. IMPORTANT INFORMATION GENERAL WARNING AND SAFETY INSTRUCTIONS The general introductory warning information must be followed. -> Read the whole of the manual thoroughly before commissioning the fire. -> Only approved transport aids with adequate load bearing capacity must be used for transporting your fire. -> Your fire is not suitable for use as a ladder or scaffold -> Thermal energy is produced by burning fuel; this leads to the surface of the fire, the doors, the door and operating handles, the door glasses, the flue pipes and possibly the front wall of the fire becoming very hot....

Open the catalog to page 8
x cook - 9

9 1.2 flue pipe connection Flue pipes are a particular hazard source in respect of escape of poisonous gas and fire hazard. Obtain the advice of an appointed specialist company in respect of laying and fitting the pipes. When connecting the flue pipe to the chimney, in the area of walls cladded using wood, please follow the relevant fitting directives. 1 . 3 You must follow the flue gas formation in the event of unfavourable weather (atmospheric inversion) and the draught conditions. If too little combustion air is added smoke can enter your house or flue gases can escape. Additionally...

Open the catalog to page 9
x cook - 10

10 2. BRIEF HEATING INFORMATION SUITABLE FUELS AND FUEL QUANTITIES In principle your fire is suitable for burning dry billets. You can also burn fuels such as wood brickets. Only use dry fuel. The burning of waste of any kind, in particular plastics, damages your fire and the chimney, and is prohibited by the Emissions Protection Ruling. FUEL QUANTITIES The fire is equipped with flat firing due to the design. This means that only one layer of fuel may be placed on the existing basic embers. Please note that when a larger quantity of fuel is added, your fire will emit a larger quantity of...

Open the catalog to page 10
x cook - 11

11 The challenges of the present day and age mean that everyone must act responsibly. One of most important matters of concern is retaining our natural world. Our products are developments that comply with the most recent state of the art technology. This is an essential prerequisite for a clean, efficient and perfect functioning of our fires CLEAN BURNING The following is important for clean burning: 1. THE FIREWOOD MUST BE DRY AND UNTREATED. Recommended value < 15% rel. wood humidity. Dry and well ventilated stored wood that has been stored for 2-3 years. A fire is not a „waste...

Open the catalog to page 11
x cook - 12

12 3. INSTALLING THE FIRE Before first commissioning or after changing the location of the fire, cleaning and service work, ensure that the flue plate, as well as the wood stop (Fig. Combustion chamber, Part 22 and 23) is in the correct position. When usinga flue pipe with throttle valve, the throttle valve must be open. Care must be taken with this fire that the flue draught reaches at least the prescribed value (> 0.8 mbar). Should problems arise here, please contact your master chimney sweep Caution! Remove the sticker from the Ceran area before using your fire for the first time....

Open the catalog to page 12
x cook - 13

13 4. OPERATION STARTING THE FIRE (Illustrated: Safety clearances) In order to keep exhaust emissions as low as possible, we would ask you to keep to the following starting instructions. 1. If the fire and chimney are still cold or if there is atmospheric low pressure, then burning some paper at the start is recommended, in order to “drive” the cold out of the fire and chimney. To start heating first lay untreated paper on the floor of the combustion chamber, on top of that 0.5 kg soft wood chip and 1 kg wood (3 small billets). Pull the shaker grate handle (Part II) out completely and open...

Open the catalog to page 13
x cook - 14

14 THE FIRE PAINT ONLY HARDENS PROPERLY AFTER HEATING UP DURING USE. Do not touch the surface during heating. It is still soft. Our paints are completely harmless in accordance with the TÜV-certificate; there is no danger to health. In spite of that we recommend that the house is well ventilated several times after first heating. Heat the fire up well – this will reduce the hardening time. Hardening of the surface is complete after several proper periods of heating. All details on the nature of the fire wood and correct heating can be found in Chapter 2. ASH DRAWER (Illustrated in Fire,...

Open the catalog to page 14
x cook - 15

15 5. FITTING OPTIONS MAKING AN EXTERNAL COMBUSTION AIR FEED (Optional: Fig: Panel) -> Dismantle the rear wall as follows: Remove the 4 decorative screws and silicone disks (Item 47, 48) and lift the Ceran area off (Item 44). Then slacken the 4 hexagon bolts (Item 49) and remove the lid (Item 43). No simply pull the rear wall upward out of the aluminium profiles (Item 50). -> Cut out the pre-stamped, round section in the rear wall (Item 46) [metal cutting saw blade]. Fasten the fresh air nozzle (must be ordered as an option) using the screws supplied and refit it to the rear wall. ->...

Open the catalog to page 15

All Rika catalogs and technical brochures

Archived catalogs

  1. visio

    33 Pages

  2. topo

    36 Pages

  3. rio

    33 Pages

  4. Revo

    34 Pages

  5. Memo

    36 Pages

  6. Integra II

    32 Pages

  7. Como

    36 Pages

  8. Twist

    20 Pages

  9. tara

    24 Pages

  10. Scena

    19 Pages

  11. Jazz

    20 Pages

  12. Eco Plus

    20 Pages

  13. Eco

    20 Pages

  14. Cult Plus

    20 Pages

  15. Cult

    20 Pages

  16. Alpha II

    19 Pages