topo
36Pages

{{requestButtons}}

Catalog excerpts

topo - 1

- 1 - TOPO Instruction Manual

Open the catalog to page 1
topo - 3

- 3 - DIMENSIONS Fresh air connection Flue blower

Open the catalog to page 3
topo - 4

- 4 - SPARE PART OVERVIEW

Open the catalog to page 4
topo - 5

- 5 - SPARE PART OVERVIEW Pos Designation Article number 1 Pressure spring 108131 2 Hinge BA1 B15825 3 Clamping ring Z11915 4 Induced draft fan housing B15452 Induced draft fan cpl. B15913 6 Induced draft fan motor 111581 8 Control panel B15621 9 Motherboard C1 air assembly B15856 10 Auxiliary board B16030 11 Stone retaining bracket L01598 12 Support stone bracket L01752 13 Cleaning opening Z33973 14 Stone retainer B16265 15 Screw B16183 16 Connecting bend cpl. B16172 17 Connecting bend for flue pipe outlet, side B16251 18 Ash tray L01611 19 Inner lining, rear left Z33708 20 Inner lining,...

Open the catalog to page 5
topo - 8

- 8 - E N G L I S H TECHNICAL DATA (Figure page 3) TECHNICAL DATA Dimensions (mm) and weights (kg) Height [mm] 1082 Width [mm] 720 Depth of the corpus [mm] 417 Weight excluding casing [kg] 166 Weight with soapstone [kg] 230 Flue pipe outlet diameter [mm] 100 Fresh air connection diameter [mm] 50 Heat output range [kW] 3 – 10 Room heating capacity depending on house insulation [m³] 70 – 260 Fuel consumption [kg/h] up to 2.4 Pellet container capacity [kg] 47 Mains connection [V]; [Hz] 230V/50Hz Average electrical power consumption [W] < 100 Protection [A] 1.6 T Efficiency [%] 91 CO2 content...

Open the catalog to page 8
topo - 9

- 9 - E N G L I S H 1. IMPORTANT INFORMATION GENERAL WARNING AND SAFETY INFORMATION Observance of the introductory general warning information is imperative . Read the entire manual thoroughly prior to putting the stove into operation. . Only approved transport equipment with sufficient load carrying capacity may be used with your heating appliance. . The burning of fuel releases heat energy that leads to extensive heating of the stove surfaces, doors, door and operating handles, glass, flue pipes and possibly the front wall. Refrain from touching these parts without appropriate protective...

Open the catalog to page 9
topo - 10

- 10 - E N G L I S H 2. WHAT ARE PELLETS? Pellets are made from wood waste from sawmills and planning mills as well as from windfall / thinning. This starting product is shredded, dried and pressed to form fuel pellets without any binders. SPECIFICATIONS FOR HIGH-QUALITY PELLETS: This specification does not conform to ÖNORM M 7135 (ash content 0.5% density) Please request tested fuel and a list of monitored fuel manufacturers from your pellet stove dealer. Use of poor quality or non-approved pellet fuel impairs the function of your stove and may lead to lapsing of the warranty, guarantee...

Open the catalog to page 10
topo - 11

- 11 - E N G L I S H 3. TECHNOLOGY The technological advances in your new pellet stove are the result of years of testing and practical experience. The practical advantages of your pellet stove are convincing: EASY OPERATION AND OPERATIONAL SAFETY Electronic monitoring and combustion temperature monitoring regulate and control the interaction of flue gas blower, screw conveyor and combustion chamber temperature. This monitoring system ensures optimum combustion and operation status. Your operating input is thus reduced to a minimum – this prevents operating errors with optimum operation....

Open the catalog to page 11
topo - 12

- 12 - E N G L I S H 5. INSTALLATION OF THE STOVE GENERAL INFORMATION . The unit must be connected to a chimney approved for solid fuels. The chimney must have a diameter of at least 120 mm. . The smoke extraction system is based on negative pressure in the combustion chamber and a slight excess pressure in the flue gas outlet. Therefore it is important that the flue connection is installed correctly and airtight. Only use heat-resistant sealing materials as well as corresponding sealing strips, heat-resistant silicon and rock wool. Assembly may only be performed by authorised specialist...

Open the catalog to page 12
topo - 13

- 13 - E N G L I S H COMBUSTION AIR Every combustion process requires oxygen or air. This combustion air is taken from the living space without an external combustion air connection for single stoves. This air removed must be replaced in the living space. Very tightly sealed windows and doors in modern flats may mean that too little air replaces that used. The situation also becomes problematical due to additional venting in flats (e.g. in the kitchen or WC). If you cannot feed in external combustion air, then air the room several times a day to prevent negative pressure in the room or poor...

Open the catalog to page 13
topo - 14

- 14 - E N G L I S H page 4-5) locks in place. Please watch your fingers when doing this. 2. Remove the 2 vertical hexagon bolts which are used for securing the left-hand side casing panel (part 51, page 4-5). 3. You can now raise the left-hand side casing panel and place it on a soft surface. DISASSEMBLING THE RIGHTHAND SIDE CASING PANEL (Image on page 4) 1. Open the container cover (part 59, page 4-5). 2. Remove the hexagon bolt that is used for securing the right-hand side casing panel (part 53, page 4-5). 3. You can now raise the right-hand side casing panel and place it on a soft...

Open the catalog to page 14
topo - 15

- 15 - E N G L I S H SIMPLE HEATING OPERATION – EASY MODE – THE FIRST STEPS Your stove is in simple heating mode EASY OFF when delivered in order to ease your start in the world of RIKA pellet stoves. The heat output of the stove can only be increased or reduced in 5 % increments in this mode. As soon as the stove is connected to the socket, the standard display EASY OFF appears. EASY OFF – INACTIVE STATE Key Display Description EASY OFF Standard display for stove switched off in simple heating mode. The output can also be regulated between 30% and 100% with the stove switched off (EASY 30...

Open the catalog to page 15
topo - 16

- 16 - E N G L I S H STOPPING UNTIL IGNIT- OR STARTPHASE If switching off occurs again 50 sec. within switching on ( key) (at least 2 sec. key), the pellet stove returns to inactive status. If switching off occurs during the ignition process (IGNIT or START) (at least 2 sec. key), IGNIT OFF or START OFF appears in the display and the burn-out phase is initiated (duration approx. 10 min). EASY 40 – OPERATION Key Display Description EASY 40 Standard display for stove switched on in simple heating mode. (40 is the output in %) EASY 45 Pressing increases output by 5% EASY 40 Pressing decreases...

Open the catalog to page 16

All Rika catalogs and technical brochures

Archived catalogs

  1. x cook

    21 Pages

  2. visio

    33 Pages

  3. rio

    33 Pages

  4. Revo

    34 Pages

  5. Memo

    36 Pages

  6. Integra II

    32 Pages

  7. Como

    36 Pages

  8. Twist

    20 Pages

  9. tara

    24 Pages

  10. Scena

    19 Pages

  11. Jazz

    20 Pages

  12. Eco Plus

    20 Pages

  13. Eco

    20 Pages

  14. Cult Plus

    20 Pages

  15. Cult

    20 Pages

  16. Alpha II

    19 Pages