Cult
20Pages

{{requestButtons}}

Catalog excerpts

Cult - 5

- 5 - S P A R E P A R T O V E R V I E W Item Description Articlenumber 1 Flue pipe connection Z10020 2 Cooking cover Z10021 3 Door closure B12322 4 riddle plate Z25948 5 Glass holder L00475 6 Suction connection Z32671 7 Regulator knob Z33349 8 Adjustment plate L01136 9 Ash drawer L00867 10 Wood retainer Z33583 11 Air intake regulator B16018 12 Riddle grate lever L01403 13 Cover Z33680 14 Lock-in spigot Z33777 15 Regulator panel B16035 16 Regulator knob shaft B16084 17 Front liner rear Z33705 18 Front liner right Z33706 19 Front liner left Z33707 20 Deflector plate top Z33712 21 Deflector...

Open the catalog to page 5
Cult - 6

- 6 - C O N T E N T S Dimensions 3 Spare part overview 4-5 Explanations to symbols 6 Packaging 7 Technical data 7 1. Important information General warning and safety information 8 Prior to set-up 8 2. A small study of heating Suitable fuels 10 Fuel quantities 10 Maximum fuel quantity 10 Clean burning 11 Burning wood 11 3. Installation of the stove Connecting the stove 12 Connecting an external combustion air infeed 12 4. Operation Fire lighting 13 Ash drawer 14 Operating the riddle grate 14 Control knob 14 5. Assembly options Retrofitting flue pipe connection top to rear connection 15 6....

Open the catalog to page 6
Cult - 7

- 7 - E N G L I S H PACKAGING Your first impression is important to us! The packaging of your new stove provides excellent protection against damage. However damage to the stove and accessories may still occur during transport. Therefore please check your stove on receipt for damage and completeness! Report any deficiencies to your dealer immediately! Pay particular attention during unpacking that the stone and ceramic panels remain intact. Scratches to the material can easily occur. Natural stone and ceramic panels are excluded from the warranty. The packaging of your new stove is...

Open the catalog to page 7
Cult - 8

- 8 - E N G L I S H 1 . I M P O R T A N T I N F O R M A T I O N Please read these instructions before installation and operation. Observe the national provisions and laws as well as the regulations and rules applicable locally. GENERAL WARNING AND SAFETY INFORMATION Observe the introductory general warning information - Read the entire manual thoroughly before putting the stove into service. - Only approved transport equipment with sufficient load carrying capacity may be used with your heating appliance. - Your heating appliance is not suitable for use as a ladder or stationary...

Open the catalog to page 8
Cult - 9

- 9 - E N G L I S H 1.3 Observe the formation of flue gas (atmospheric inversion) and draughts when the weather is unfavourable. Infeed of too little combustion air can lead to smoke in the rooms or to flue gas leaks. Hazardous deposits in the stove and chimney may also occur. If flue gas escapes, let the fire burn out and check whether all the air inlet openings are free and the flue gas pipes and the stove pipe are clean. If in doubt notify the master chimney sweep since draught malfunctions may be connected to your chimney. 1.4 Push the embers together to form a firebed when you add new...

Open the catalog to page 9
Cult - 10

- 10 - E N G L I S H 2 . A S M A L L S T U D Y O F H E A T I N G SUITABLE FUELS AND FUELS QUANTITIES Your stove is generally suitable for burning dry firewood. You can also burn fuels such as wood briquettes. Only use dry fuel (moisture content between 14 and 18 %). Burning waste of any kind, particularly plastic, damages your stove and chimney and is prohibited by the emission reduction laws. FUEL QUANTITIES The stove is fitted with a construction-specific flat firebox. This means only one layer of fuel may be laid on the base embers. Please observe that adding greater quantities of fuel...

Open the catalog to page 10
Cult - 11

- 11 - E N G L I S H Facing the challenges of our times means assuming responsibility. Maintaining our natural world is now one of our most important tasks. Our products represent developments according to the state of the art. This is the main precondition for clean, efficient and problem-free working of our stoves. CLEAN BURNING Clean combustion requires: 1. DRY AND UNTREATED FIREWOOD. Guideline between 14 % and 18 % relative wood moisture. Wood stored dry and ventilated for 2 – 3 years. A stove is not a waste incinerator. The warranty lapses if waste or non-approved materials such as...

Open the catalog to page 11
Cult - 12

- 12 - E N G L I S H 3 . I N S T A L L A T I O N O F T H E S T O V E Ensure that the deflector plate (page 4-5, part 20) is correctly positioned prior to initial commissioning and after relocation, cleaning and service work. The damper flap must be open in the flue pipe. Ensure with this stove that the chimney draught reaches at least the value specified (10 Pa). If there are any problems with this, contact your master chimney sweep. CONNECTING THE STOVE Proceed as follows for new connections in a brick-built chimney: 1. Measure and mark out the stove connection (take into consideration any...

Open the catalog to page 12
Cult - 13

- 13 - E N G L I S H 4 . O P E R A T I O N FIRE LIGHTING To reduce the emission of pollutants as far as possible, we ask you to observe the following instructions for the sake of the environment. 1. If the stove and chimney are still cold or if there is atmospheric low pressure, we recommend burning some paper initially to remove the cold from the stove and chimney. 2. To light the fire, place uncoated paper at the bottom of the combustion chamber, then 0.5 kg softwood chippings and 1 kg wood (3 small logs). Turn the regulator knob to the right to fire lighting setting; primary and...

Open the catalog to page 13
Cult - 14

- 14 - E N G L I S H THE STOVE COATING ONLY CURES COMPLETELY ON INITIAL USE DUE TO THE HEAT . - Do not touch the surface during heating. . It is still soft. - Our coatings are harmless according to TÜV report; a hazard to health can be ruled out. However, we recommend airing the flat after initial heating several times. - Heat the stove extensively - this shortens the curing time. - the curing of the surface is complete after some proper heating processes. Please see Chapter 2 for all information on the composition of firewood and correct heating. ASH DRAWER (Page 4-5, part 9) The ash...

Open the catalog to page 14
Cult - 15

- 15 - E N G L I S H 5 . A S S E M B L Y O P T I O N S RETROFIT FLUE GAS PIPE TOP TO REAR CONNECTION - Lift the cast cover (part 13) off. - Cut the prestamped round hole in the rear wall (part 42) using a hacksaw. - Swap the flue connections and the cooking cover (parts 1, 2) - Replace the cast cover. (Take care of your fingers!)

Open the catalog to page 15

All Rika catalogs and technical brochures

Archived catalogs

  1. x cook

    21 Pages

  2. visio

    33 Pages

  3. topo

    36 Pages

  4. rio

    33 Pages

  5. Revo

    34 Pages

  6. Memo

    36 Pages

  7. Integra II

    32 Pages

  8. Como

    36 Pages

  9. Twist

    20 Pages

  10. tara

    24 Pages

  11. Scena

    19 Pages

  12. Jazz

    20 Pages

  13. Eco Plus

    20 Pages

  14. Eco

    20 Pages

  15. Cult Plus

    20 Pages

  16. Alpha II

    19 Pages