Alpha II
19Pages

{{requestButtons}}

Catalog excerpts

Alpha II - 1

ALPHA II Instruction Manual

Open the catalog to page 1
Alpha II - 3

Fig. 3 Version: Stahlmantel Version: Steel casing Versione: rivestimento in acciaio Version: Manteau en acier

Open the catalog to page 3
Alpha II - 4

Fig. 4 Fig. 6 Version: Speckstein Version: Whetstone Versione: rivestimento in steatite Version: stéatite Fig. 5

Open the catalog to page 4
Alpha II - 5

Fig. 7 Fig. 8 Fig. 9 Fig. 10 Fig. 11 Fig. 12 Kohlendioxid Carbon dioxide Anidride carbonica Dioxyde de carbone Sauerstoff Oxygen Ossigeno Oxygène Wasser Water Acqua Eau CO2 O2 H2O CO2 25 cm 7 cm 1,6 kg

Open the catalog to page 5
Alpha II - 6

5 . GUARANTE E 4 . CLEAN I NG AND MAI NTENANCE 3 . OPE RATION E X P L A N A T I O N O F S Y M B O L S 2 . INSTALLATION OF THE APPLIANCE 1. IMPORTANT INFORMATION L I S T O F C O N T E N T S Important instructions Practical advice Use the fold out plan for assistance Overview of technical data and spare parts 19 General warning and safety instructions 20 Before installing the appliance 20 - 21 INFORMATION ON HEATING PRACTICE Suitable fuels and quantities 22 Fuel quantities 22 Maximum fuel quantities 22 Clean combustion 23 Burning of wood 23 Changing the draw plate 24 Inserting the whetstone...

Open the catalog to page 6
Alpha II - 7

TECHNICAL DATA Dimensions (mm) and weights (kg) Height 905 Width 516 Depth of the corpus 395 Weight with steel casing 115 Weight with stone casing 155 Smoke flue outlet diameter 130 Nominal heating power (DIN 18891) 7 kW Lowest heating power 3,5 kW Space heating capacity (m³) – dependent on house insulation 70-190 Fuel flow 1,4 kg/h Efficiency 78,9 % CO2 content 10,2 % CO emission rel. 13% O 734 mg/Nm3 Dust emissions 29 mg/Nm3 Exhaust gas values for multiple use of the chimney in accordance with DIN 4705, Part 3/chimney dimensions to DIN 4705, Part 2 Exhaust gas mass flow g/s 8,68 Exhaust...

Open the catalog to page 7
Alpha II - 8

1. I M P O R TA N T I N F O R MAT I O N ENGLI S H 20 GENERAL WARNING AND SAFETY INSTRUCTIONS The introductory general warning and safety instructions must be unconditionally observed . Before commissioning the heater, read this handbook thoroughly in its entirety. . Only an approved means of transport, with adequate load carrying capacity must be used to transport your heating appliance. . Your heating appliance is not suitable for use as a ladder or supporting platform. . The burning of fuel releases heat energy, leading to considerable heating of the surface of the heating appliance, the...

Open the catalog to page 8
Alpha II - 9

21 ENGLI S H 1 . 3 Be sure to note the build-up of flue gases under unfavourable weather conditions (Weather inversion) and the flue draft behaviour. If too little air for combustion is taken in, this can lead to fumes in the room in which the appliance is located, or result in the escape of flue gases. In addition, damaging deposits can be formed in the appliance and in the chimney. In the event of the escape of fumes, let the fire go out and check that all the air inlet openings are unobstructed and that the flue gas ducting and flue are clean. In case of doubt, advise a registered...

Open the catalog to page 9
Alpha II - 10

ENGLI S H 22 I N F O R MAT I O N O N H E AT I N G P R ACT I C E SUITABLE FUELS AND QUANTITIES Your appliance is basically suitable for the burning of dry chopped firewood. In addition, you can burn fuels such as wood briquettes and brown coal briquettes. Use only dry material for burning. The burning of refuse of any kind, particularly plastics, will damage your appliance and the chimney and is prohibited by the statutory regulations on emissions. FUEL QUANTITIES The appliance is designed with a flat firing layout, due to its style of construction. This means that only one layer of fuel...

Open the catalog to page 10
Alpha II - 11

23 ENGLI S H Satisfying the challenges of our time implies the acceptance of responsibility. The conservation of nature is now one of our greatest challenges. Our products are developments that correspond to the latest state of the art technology. This is an essential prerequisite for the clean, efficient and law-abiding functioning of our firing appliances. CLEAN COMBUSTION The following are important to the achievement of clean combustion: 1. THE WOOD TO BE BURNED MUST BE DRY AND UNTREATED. (Fig. 11) Standard value ‹ 15 % rel. humidity in the wood. 2 - 3 years drying and well ventilated...

Open the catalog to page 11
Alpha II - 12

CHANGING THE DRAW PLATE (Fig. 5) If the draw plate or the draw-deflector is to be replaced on your firing appliance, lift the draw plate slightly to the side and remove the side fireclay component. You can now tilt the draw plate and remove it from the firebox opening. Before initial commissioning or after re-locating the appliance, cleaning and servicing, make sure that the draw plate (Fig. 5, Part 18), and the wood collector (Fig. 5, Part 21) are correctly positioned. When using a flue with a throttle flap, this must be open. On this firing appliance, it is necessary to ensure that the...

Open the catalog to page 12
Alpha II - 13

FIRING UP (Fig. 12) In order to suppress the emission of pollutants as far as possible, we would ask you - for the sake of the environment - to adhere to the following instructions for heating up your firing appliance. 1. If your appliance and chimney are cold, or if low atmospheric pressure prevails, it is recommended that initially you burn some paper, to “drive” the coldness from the appliance and the chimney. 2. For the purpose of heating up, first lay some uncoated paper on the floor of the firebox and on top of this place 0.5 kg of softwood chippings and 1.4 kg of wood (2 logs). Pull...

Open the catalog to page 13
Alpha II - 14

ENGLI S H 26 THE ENAMEL APPLIED TO YOUR HEATING APPLIANCE BECOMES FULLY HARDENED THROUGH HEATING DURING INITIAL USE. - Do not touch the surface during initial heating. It will still be soft. - To draw off the fumes that are liberated, ensure that the area housing the appliance is well ventilated and do not prepare food in the vicinity of the appliance. - Heat up the appliance thoroughly - this will shorten the hardening time. - The hardenimg of the surface will be complete after several routine heating operations. Please refer to Chapter 1 for details of the wood fuel to be burned and the...

Open the catalog to page 14
Alpha II - 15

4 . C L E A N I N G A N D M A I N T E N A N C E ENGLI S H 27 GENERAL MAINTENANCE Your ALPHA II appliance has been designed by our development team with the concepts of minimum maintenance and long operating life very much in mind. Certain cleaning operations and the checkin of seals are necessary from time to time. The time between inspections depends to a large extent on the quality of the wood you burn and frequency of use. All maintenance and cleaning work must be undertaken exclusively when the appliance has completely cooled down. A REMINDER Only use wood that has been properly stored,...

Open the catalog to page 15

All Rika catalogs and technical brochures

Archived catalogs

  1. x cook

    21 Pages

  2. visio

    33 Pages

  3. topo

    36 Pages

  4. rio

    33 Pages

  5. Revo

    34 Pages

  6. Memo

    36 Pages

  7. Integra II

    32 Pages

  8. Como

    36 Pages

  9. Twist

    20 Pages

  10. tara

    24 Pages

  11. Scena

    19 Pages

  12. Jazz

    20 Pages

  13. Eco Plus

    20 Pages

  14. Eco

    20 Pages

  15. Cult Plus

    20 Pages

  16. Cult

    20 Pages