Regupol® Insulation and Building Protection
20Pages

{{requestButtons}}

Catalog excerpts

Regupol® Insulation and Building Protection - 1

Insulation and Building Protection Roof membrane p rotection on flat roofs or under solar panel racks

Open the catalog to page 1
Regupol® Insulation and Building Protection - 3

Building Protection Protection against Mechanical Damage BSW is one of the market leaders with its range of insulation and building protection products. Alongside its top-selling product, Regupol® resist, BSW has developed other special products that fulfil, due to their particular properties, specific applications and requirements. Low cost and easy installation offer clear advantages compared to protective screed, protection concrete and facing brickwork. Structural defects, such as caused by damaged membranes and insulations, can be avoided, reliably and durably. Regupol® Insulation and...

Open the catalog to page 3
Regupol® Insulation and Building Protection - 4

Building Protection Application Areas Regupol® resist Flat Roofs under gravel, flower pots, slab paving, roof plantings, etc. Terraces and Balconies under concrete slabs, (wooden) tiles, etc. Parking Decks under concrete or bituminous surfacing Inverted Roofs under gravel, slab paving, raised floors, etc. Building Construction and Civil Engineering for concrete construction, bridge construction, covered parking decks, underground car parks, head race tunnels, tunnel constructions, avalanche galleries, bunkers, hangars, ammunition dumps Pipeline Construction for covering of dome-shaped cuts...

Open the catalog to page 4
Regupol® Insulation and Building Protection - 5

Building Protection Regupol® resist Regupol® resist is the most versatile product to protect membranes and insulations. It is made of PUR-bonded rubber fibres and granules. Regupol® resist is classified as a protective layer in accordance with DIN 18531. In comparison to protective screed and concrete, Regupol® resist possesses clear technical, physical and financial advantages. It is easy to install and can be optimally bonded to any kind of sub-bases by means of hot bitumen, special adhesives and plastic adhesives. Material PUR-bonded rubber fibres and granules Weight per unit approx. 6...

Open the catalog to page 5
Regupol® Insulation and Building Protection - 6

Building Protection Chemically compatible with all types of membranes Regupol® resist solar AK Protective Layer underneath Solar Systems With this product, Regupol® resist solar AK offers a selection of protective layers that has been specifically developed for the installation of photovoltaic systems on flat roofs. The protective layers are marked by their extremely long product life as well as their high mechanical load-bearing capacity. A large selection of product alternatives allows users to find the fitting protective layer for the different types of flat roofs and solar plants....

Open the catalog to page 6
Regupol® Insulation and Building Protection - 7

Building ProtectionRegupol® resist solar AK - Technical Details Material Prefabricated PUR-bound rubber granulate with optional fire protection finish and underside lined with triplex aluminium foil. Tile Measurements 6,000 x 1,250 x 10 mm 6 rolls per euro pallet Customized goods in different lengths, thicknesses (possible thicknesses up to 20 mm) and widths (beginning from 50 mm) are available on request. Weight per unit approx. 4.5 kg/m2, at 6 mm thickness Low-Temperature Stability to -40 °C Thermostability to +90 °C Tensile Strength of the Triplex Aluminium Foil under tensile load ctr =...

Open the catalog to page 7
Regupol® Insulation and Building Protection - 8

Building Protection Regupol® resist solar - Product Varieties Also suitable for the protection of flat roof installations : Roofing and Pavement Tiles :walkway AK 1 2 Yes Chemically compatible with all types of membranes. Flame-resistant: classification BRoof (t1) according to DIN EN 13501-5 after DIN V ENV 1187 test. These four Regupol® building protection sheets are generally used for the protection of rubber-compatible roof membranes. They are also suitable underneath solar systems and other types of structures. Protected by German utility model (issued by the German Patent and Trade...

Open the catalog to page 8
Regupol® Insulation and Building Protection - 9

Building Protection Regupol® drain plus Regupol® drain plus provides both a protection and drainage layer. The top side of Regupol® drain plus is laminated with a fibre fabric which allows only liquids to seep through. The profiled underside makes sure that liquids can drain off. Regupol® drain plus possesses high mechanical load capacity, does not corrode and is spade-resistant. Material PUR-bonded rubber granules and fibres (rough); fleece lamination Weight per unit approx. 7.5 kg/m2 Roll dimension 10,000 x 1,250 x 8/12 mm 4 rolls per euro pallet Low-Temperature Stability to -40 °C...

Open the catalog to page 9
Regupol® Insulation and Building Protection - 10

Building Protection Regupol® resist FH The Regupol® resist FH building protection sheet is the new product from BSW to protect membranes and insulation, and to reduce the fire load on flat roofs. The flame-retardant equipment makes the sheets made of PUR-bound rubber granulates resistant against flying sparks and radiant heat. The fire resistance rating is considerably enhanced from a fire protection point of view. Regupol® resist FH insulation and building protection with a thickness of 8 mm is classified as BRoof (t1) and therefore considered to be hard roofing. Under certain...

Open the catalog to page 10
Regupol® Insulation and Building Protection - 11

Building Protection 11 Regupol® resist FH - Technical Details Material PUR-bound rubber granulate with fire protection finish Tile Measurements 8,000 x 1,250 x 8 mm 11 rolls on a europallet Weight per unit approx. 6 kg/m2 Low-Temperature Stability to -40 °C Thermostability to +120 °C, when installing under bituminous base course/hot bitumen, please keep the linear thermal expansion coefficient in mind (for further information please feel free to contact BSW). Tensile Strength under tensile load ctr = 0.50 N/mm2, in accordance with DIN EN ISO 1798 Elongation at Break Yr = 40 %, in accordance...

Open the catalog to page 11
Regupol® Insulation and Building Protection - 12

Building Protection Regupol® resist 9510 Regupol® resist 9510 is an alternative to Regupol® resist for protective roof membranes and insulation, as well as for higher loads. Regupol® resist 9510 consists of PUR-bonded butyl rubber and is classified as a protective layer in accordance with DIN 18531. In comparison to protective screed and concrete, Regupol® resist 9510 possesses clear technical, physical and financial advantages. It is easy to install and can be optimally bonded to any kind of sub-bases by means of hot bitumen, special adhesives and plastic adhesives. The material is...

Open the catalog to page 12

All REGUPOL BSW GmbH catalogs and technical brochures

Archived catalogs