Symmetrical Cladding lying instruction
9Pages

Symmetrical Cladd Laying instructions

These laying instructions describe the application of InterSIN® slate, SIN 970 and ColorSIN®, CS 35 or CS 50 together with the aluminium substructure included with delivery and the corresponding mounting materials as a complete system. The instructions are the basis for appropriate planning and application-oriented technical solutions in usual situations. The detail drawings found in the laying instructions depict some of the standard details of the symmetrical cladding. The following pages contain technical information about the curtain-type, rearventilated facade and practical guidelines...

The most current versions of these fundamental rules must be followed in principle: u he symmetrical cladding is a curtain-type, rearT u ll of the stones used have come from the same A ventilated facade cladding. It consists of InterSIN® u DIN 4102 Fire behaviour of building materials and deposit. Colour fluctuations are possible. These slate, SIN 970 and ColorSIN , CS 35 or CS 50, a rear nuances and the individual structure of each stone ventilation gap, thermal insulation and an aluminium make up the natural charm of each slate roof and are deliberate. Slate stones from the various...

Slate for symmetrical cladding is available in 3 colour variants and 2 surface variants: Surface natural or polished ► ColorSIN®, CS 35: dark green Surface natural ► ColorSIN®, CS 50: polar green Surface natural or polished Stone sizes: Wall bracket Fixed point HE132/150 3 x 10.5 Standard size projection (height) The wall bracket length is variable. Wall bracket Sliding point HE132/50 1 x 10.5 Standard size projection (height) The wall bracket length is variable. Mounting screw Ejot JT4-4-4.8x25 Foam rubber underlayment Teroson Spray The vertical aluminium rail is available untreated or...

4.4 External building corner To prevent annoying dripping noises from rain, it is recommended that sound damping material be installed on the underside of large surfaces such as windowsills slide and anchor points must be considered in terms of statics. The gap between the drip shield and the components beneath it must measure at least 20 mm. If copper is used, the minimum gap must measure at least 50 mm. The profile edge should overlap the slate at these building heights: u up to 8 m 4.5 Internal building corner Reveal plate of a system sash design with open, vertical joint. 11

The device for cladding the external walls of structures The aluminium substructure is a three-dimensional Affix the vertical anchor (HE132/80) and slide points The number of mounting points and the type of and buildings consists of a substructure system that can be adjusted for height, depth and lateral (HE132/50) according to static specifications. mounting material (wall plug length and extraction These bearing profiles are vertically parallel and evenly spaced relative to each other. Attach them to the building Static specifications are always material to mounting this wall at the...

Insert the wall plug and tighten the screw according to Drill holes with a diameter of 5.2 mm in the wall holders Before fixing the slide points, laterally insert a separate specifications set by building inspectors. and the vertical bearing profiles for the rivets. sliding profile (HE105) on the rear side of the bearing If statics require the use of zinc-plated screws, the screw Attach each of the vertical bearing profiles under load to head must additionally be treated with a protective the anchor points with 4 rivets 5 x 14 K11 (follow the static specifications). Install the bearing...

The lateral dovetail (clamping disk) must be mounted Mount the clamping disk with a rivet that conforms to Fasten all of the other rows to the profile with a double such that the lateral dovetail is connected to the wall clip as described earlier. holder under load. After assembling the vertical substructure, start arranging the horizontal spacing. The spacing dimensions correspond to the size of the facade stones plus joint width. Slate width for symmetrical cladding is usually approx. 600 x 300 mm or approx. 600 x 600 mm. Affix the initial clips to the lower end of the vertical bearing...

InterSIN® blue-grey, natural InterSIN® blue-grey, polished ColorSIN® polar green, natural ColorSIN® polar green, polished ColorSIN® dark-green, natural Slate is a natural product. Irregularities in colour and structure may occur. These nuances and the individual appearance of each stone make up the Rathscheck Schiefer und Dach-Systeme St.-Barbara-Straße 3 D-56727 Mayen-Katzenberg Germany Telefon +49 (0)26 51/955- 0 Telefax +49 (0)26 51/955-100 info@rathscheck.com www.rathscheck.com © by Rathscheck. Subject to revision. 07/2012 charm of slate cladding.