Dock leveller with lip PT
27Pages

Dock leveller with lip PT Data sheet Technical modifications reserved

Dock leveller with lip PT Technical modifications reserved

Dock leveller with lip PT 1. General information The PT-type dock leveller with telescopic lip is a new design in the wide range of PROMStahl products. The perfect quality of this device is a result of 20 years of experience in the field of designing and constructing dock levellers. The PT-type electro-hydraulic dock leveller is operated with buttons on the control system. When the platform is lifted to required height, the lip can be unfolded to desired length and supported on the vehicle bed. This is a great advantage of this device, since there is a possibility of docking vehicles not...

Dock leveller with lip PT 1.1 Design features Nominal lengths (NL): 1750, 2000, 2500, 2750, 3000, 3500, 4000, 4500 mm Nominal widths (NW): 1750, 2000, 2100, 2200, 2250, 2400 mm Nominal heights (NH): 600, 700, 800 mm Lip lengths (LL): 500, 1000 mm Nominal capacity: 6 tonnes (60kN) Operating ranges above level: 0 – 590 mm Operating ranges below level: 0 – 480 mm Thickness of the upper sheet of the platform: tread plate 8 mm (8/10) Platform options: anti-slip coating, insulation, EPDM gasket Lip sheet thickness: tread plate 13 mm (13/15) Lip options: corner chamfering, side segments, straight...

Dock leveller with lip PT  Standard corrosion protection: sand blasting and painting 80 µm       RAL 5010 RAL 7016 Optional corrosion protection: painting with RAL pallet paints 160 µm, hot-dip galvanizing, duplex (hot-dip galvanizing and painting) Motor power: 1.1 kW or 1.5 kW Power supply: 3~400 V, N, PE / 50Hz / 16A Control system tightness degree: IP 54 – Basic controller or IP65 – Standard controller Standard functions of the control system: two control buttons, main switch, door and wheel chock sensor connector, automatic return button Optional functions of the control system:...

Dock leveller with lip PT 1.2 Operating range NL LH 2000 Technical modifications reserved

Dock leveller with lip PT 2. Telescopic lift The lip of the PT-type dock leveller is made of high quality tread plate with thickness of 13 mm (13/15) and equipped with a special, solid, contamination-resistant and almost maintenance-free system of hinges. The system of simple, high-durability slides ensures its silent and faultless operation. There is a wide range of optional lip designs available: Technical modifications reserved

Dock leveller with lip PT Bent lip Standard solution. It ensures good work ergonomics when the vehicle deck is both below and above the docking floor level. Straight lip Solution for better work ergonomics when the vehicle deck is below the docking floor level. Bevelling 40 mm Standard solution. It ensures good ergonomics for loading devices with large and soft wheels. Bevelling 100 mm Solution improving work ergonomics, especially for loading devices with small and hard wheels. Technical modifications reserved

Dock leveller with lip PT 3. Platform The platform of the PT-type dock leveller with load capacity of 60kN is made of high quality tread plate with thickness of 8 mm (8/10) and is intended to be used with standard, four-wheel forklift trucks with pneumatic wheels or so-called super elastic wheels. Optionally, the leveller can be delivered in a version enabling operation with hard wheel devices such as electric pallet trucks. The upper sheet is reinforced from the bottom with special binders ensuring torsional flexibility of the platform. This ensures adhesion of the vehicle along the entire...

Dock leveller with lip PT 3.2 EPDM gasket In order to limit air infiltration through the dock leveller it can be optionally fitted with a gasket between the platform and the framing. This improves working conditions in the warehouse and ensures power saving. The platform can be optionally fitted with a front screen limiting the amount of contamination, air infiltration and ensuring an attractive look. Technical modifications reserved

Dock leveller with lip PT 3.4 Insulation Optional insulation of the platform ensured by panels with thickness of 40 to 60 mm reduces heat losses and the intensity of sounds transmitted by the device. It is recommended to apply insulation in combination with an EPDM gasket. 3.5 Anti-slip coating (KVS) The platform and the lip of the PT-type dock leveller can be optionally finished with special anti-slip coating with thickness of about 4 mm, consisting of flexible polyurethane layer resistant to pressure and most chemicals, as well as of fine basalt aggregate. Such combination guarantees...

Dock leveller with lip PT 4. Framing The framing provides connection of the dock leveller with the building and supports it in rest position. The PT-type dock leveller comes with a wide range of framing for each installation requirement ensuring so-called undercut for docking vehicles with a lift. 4.1 T-frame The dock leveller framing is filled with concrete. The frame around the leveller is equipped with a 200mm wall serving as a small formwork. This significantly facilitates concrete works. Quick and clean installation in one step is an advantage of this solution. Technical modifications...

Dock leveller with lip PT 4.2 W-frame The dock leveller framing is welded to the previously prepared initial frame fastened in the building floor. This solution allows you to install the leveller after completing concrete works. Potential and easy replacement of the device in future is an additional advantage. Technical modifications reserved

Dock leveller with lip PT 4.3 F-frame The dock leveller framing is welded to the existing frame. This allows you to install the leveller in a seat from which the previous leveller was removed. Technical modifications reserved

Dock leveller with lip PT 4.4 P-frame The dock leveller framing is welded to the angle bar in the rear part of the seat. The leveller is positioned at the bottom of this seat. Quick and easy installation is an advantage of this solution. Technical modifications reserved