Manual Single-leaf traffic swinging doors (TSD)
17Pages

Single-Leaf Traffic Swinging Doors (TSD)

Table of contents 1. General information __________________________________________________________ 5. TSD with an angular door frame ____________________________________________ 6. Door assembly kits for an angular frame ___________________________________________ 7. TSD with a curved "U-shaped" door frame ____________________________________ 8. Door assembly kits for a curved U-shaped door frame ________________________________ 9. TSD with an overlapping door frame ________________________________________ 10. Door assembly kits for an overlapping door frame...

After having installed the door, it is important to adjust the leaf! 1. GENERAL INFORMATION This manual outlines information pertaining to ProfHolod doors: main uses, information about the doors, technical specifications and installation instructions. All comments and suggestions for improving operations should be sent to: Russian Federation 141000, MO, Shchelkovo, st. Zavodskaya, 2, tel: +7 (495) 240-83-14, e-mail: info@profholod.com. Traffic swinging doors produced by ProfHolod are designed for doorways in places where people and low trolleys regularly pass, for operation in heated and...

2 - COLDTECH swing hinge, Italy 4. TECHNICAL SPECIFICATIONS The door leaf, including the edges, is made from 0.5 mm thick steel sheet, which protects the door leaf from impact. Rigid polyurethane foam, thermal conductivity 0.022 W/m*K. TSD can be equipped with different metal frames: "overlapping", "angular", or a curved "U-shaped" frame of 20x60. A seal of the appropriate height is included as standard, as well as a window with a rubber frame. (see "Delivery set") Please be aware that traffic swinging doors do not completely seal shut around the opening, since there are gaps along the...

Figure 4. Cross-section 1-1. TSD with flat bumper Figure 5. Cross-section 1-1. TSD with curved bumper 6. DOOR ASSEMBLY KITS FOR AN ANGULAR FRAME. Attachments and fasteners for an angular door frame: Figure 6. Assembly unit 1. Fastening a metal angular door frame to a sandwich panel 1 - TSD 2 - Door frame 3 - Erickson's nut 4 - Threaded rod М8 5 - PVC thermal washer 6 - PVC thermal nut 7 - Door hinge 8 - Moulded element 9 - Polyurethane foam

Figure 7. Assembly unit 2. Fastening a metal angular door frame to a brick wall 1 - TSD 2 - Door frame 3 - Anchor 10x92 4 - Door hinge 5 - Polyurethane foam Figure 8. Assembly unit 2. Fastening a metal angular door frame to a metal structure 1 - TSD 2 - Door frame 3 - Self-tapping screw for roofing 6,3х32 4 - Door hinge 5 - Polyurethane foam 7. TSD with a curved "U-shaped" door frame The standard curved door frame has a 20x60 profile and is painted with powder enamel paint in RAL 9003 or any other colour from the RAL catalogue. Available in stainless steel AISI 304 or AISI 430. The frame is...

Figure 11. Cross-section 1-1. TSD with flat bumper Figure 12. Cross-section 1-1. TSD with curved bumper 8. DOOR ASSEMBLY KITS FOR A CURVED U-SHAPED DOOR FRAME Attachments and fasteners for a curved U-shaped door frame: Figure 13. Assembly unit 1. Fastening the "U-shaped" frame to a brick wall 1 - TSD 2 - "U-shaped" door frame 3 - Anchor 10x92 4 - Door hinge 5 - Polyurethane foam

Figure 14. Assembly unit 1. Fastening the "U-shaped" frame to a metal structure 1 - TSD 2 - "U-shaped" door frame 3 - Anchor 10x92 4 - Door hinge 5 - Polyurethane foam 9. TSD WITH AN OVERLAPPING DOOR FRAME The standard overlapping door frame is made from 2 mm thick cold rolled steel sheet and painted with powder enamel paint in RAL 9003 or any other colour from the RAL catalogue. Available in stainless steel AISI 304 or AISI 430. The frame is mounted onto both sides of the opening using a mounting kit (optional), and can be mounted to the following: • An opening in a wall made of sandwich...

10. DOOR ASSEMBLY KITS FOR AN OVERLAPPING DOOR FRAME Attachments and fasteners for an overlapping door frame: Figure 19. Assembly unit 1. Fastening an overlapping frame to a sandwich panel 1 - TSD 2 - door frame 3 - Erickson's nut 4 - Threaded rod М8 5 - Door hinge 6 - Self-tapping screw for fastening the frame components Figure 20. Assembly unit 2. Fastening an overlapping frame to a brick wall * 1 - TSD 2 - Door frame 3 - Anchor 10x92 4 - Self-tapping screw for fastening the frame components 5 - Door hinge * - wall thickness cannot be less than 160 mm 11. INSTALLATION OF SWING DOORS WITH...

12. INSTALLATION OF SWING DOORS WITH A CURVED U-SHAPED DOOR FRAME ● Before installing the doors, make sure that the leaves were not damaged during transportation. Check all parts are accounted for. ● Check the dimensions of the opening against the dimensions indicated in the door specification. Any deviation of the dimensions of the width and height of the opening cannot exceed ± 5 mm. Any diagonal deviation can also only be ± 5 mm. ● Unscrew the 4 fasteners from each hinge and remove the blade. ● Install the frame into the opening and check both levels: the posts vertically and the...

14. DOOR BLOCK ADJUSTMENT ● Stiffness adjustment or adjustment of the door opening force with COLDTECH swing hinges: 1. Remove the door leaf from the hinges by unscrewing the 4 screws securing the half-hinge. 2. Adjust the pressure with the adjusting screws. 3. Re-hang the door leaf and re-tighten the fastening screws. ● Stiffness adjustment or door opening force adjustment with KIDE pendulum hinges: 1. Remove the door leaf from the hinges by unscrewing 4 screws securing the half-hinge. 2. Adjust the pressure of the adjustment bolt. 3. Re-hang the door leaf and re-tighten the fastening screws

● Adjusting the position of the door leaf in the opening: 1. Open the door to 90º. 2. Adjust the door position with the adjusting bolts. 3. Close the door. 15. OPERATION AND MAINTENANCE INSTRUCTIONS The effective operation and service life of hinged doors is largely dependent on the quality and regularity of maintenance. For a trouble-free and long-term operation of the fittings, it is recommended to schedule an inspection of the fittings, to tighten the fasteners and lubricate the surfaces that experience friction at least once every two weeks. The frequency of maintenance may vary...