Manual Double-leaf traffic swinging doors (TDD)
20Pages

Double Leaf Traffic Swinging Doors (TDD)

Table of contents 1. General information _____________________________________________________________ 3 2. Purpose and use _______________________________________________________________ 3 3. Specifications _________________________________________________________________ 3 4. Technical specifications _________________________________________________________ 4 5. TDD doors with an angular door frame ______________________________________________ 4 6. Door assembly kits for an angular frame ____________________________________________ 7 7. TDD doors with a curved “U-shaped” door frame...

After having installed the door, it is important to adjust the leaf! This manual outlines information pertaining to ProfHolod doors: main uses, information about the doors, technical specifications and installation instructions. All comments and suggestions for improving operations should be sent to: Russian Federation, 141000, MO, Shchelkovo, st. Zavodskaya, 2, tel: +7 (495) 240-83-14, e-mail: info@profholod.com. Traffic swinging doors produced by ProfHolod are designed for doorways in places where people and low trolleys regularly pass, for operation in heated and unheated rooms with a...

2 - COLDTECH swing hinge, Italy 4. TECHNICAL SPECIFICATIONS The door leaf, including the edges, is made from 0.5 mm thick steel sheet, which protects the door leaf from impact. Rigid polyurethane foam, thermal conductivity 0.022 W/m*K. TDD can be equipped with different metal frames: overlapping, angular, or a curved U-shaped frame of 20x60. A seal of the appropriate height is included as standard, as well as a window with a rubber frame. (see "Delivery set"). Please be aware that traffic swinging doors do not completely seal shut around the opening, since there are gaps along the perimeter...

Figure 3. TDD with a metal angular frame. Figure 4. Cross-section 1-1. TDD with curved bumpers

Figure 5. Cross-section 1-1. TDD with flat bumpers 6. DOOR ASSEMBLY KITS FOR AN ANGULAR FRAME Attachments and fasteners for an angular door frame: Figure 6. Assembly unit 1. Fastening a metal angular door frame to a sandwich panel 1 - TDD 2 - Door frame 3 - Erickson's nut 4 - Threaded rod М8 5 - PVC thermal washer 6 - PVC thermal nut 7 - Door hinge 8 - Moulded element 9 - Polyurethane foam Figure 7. Assembly unit 2. Fastening a metal angular door frame to a brick wall 1 - TDD 2 - Door frame 3 - Anchor 10x92 4 - Door hinge 5 - Polyurethane foam

Figure 8. Assembly unit 2. Fastening a metal "angular door frame to a metal structure 1 - TDD 2 - Door frame 3 - Self-tapping screw for roofing 6,3х32 4 - Door hinge 5 - Polyurethane foam 7. TDD SET WITH A CURVED U-SHAPED DOOR FRAME The standard curved door frame has a 20x60 profile and is painted with powder enamel paint in RAL 9003 or any other colour from the RAL catalogue. Available in stainless steel AISI 304 or AISI 430. The frame is mounted onto the inside of the opening using the mounting kit (optional), and can be mounted to the following: ● The opening of load-bearing walls, made...

Figure 10. TDD with metal U-shaped frame Figure 11. Cross-section 1-1. TDD with curved bumper

Figure 12. Cross-section 1-1. TDD with flat bumper 8. DOOR ASSEMBLY KITS FOR A CURVED U-SHAPED FRAME Attachments and fasteners for a curved U-shaped door frame: Figure 13. Assembly unit 1. Fastening the U-shaped frame to a brick wall 1 - TDD 2 - U-shaped door frame 3 - Anchor 10x92 4 - Door hinge 5 - Polyurethane foam Figure 14. Assembly unit 2. Fastening the U-shaped frame to a metal structure 1 - TDD 2 - U-shaped door frame 3 - Anchor 10x92 4 - Door hinge 5 - Polyurethane foam 9. TDD SET WITH AN OVERLAPPING DOOR FRAME The standard overlapping door frame is made from 2 mm thick cold rolled...

Available in stainless steel AISI 304 or AISI 430. The frame is mounted onto both sides of the opening using a mounting kit (optional), and can be mounted to the following: ● An opening in a wall made of sandwich panels or drywall ● An opening in a wall made of concrete or brick Figure 15. Metal overlapping door frame Figure 16 TDD with metal overlapping door fram

Figure 17. Cross-section 1-1. TDD with cured bumper Figure 18. Cross-section 1-1. TDD with flat bumper

10. DOOR ASSEMBLY KITS FOR AN OVERLAPPING DOOR FRAME Attachments and fasteners for an overlapping door frame: Figure 19. Assembly unit 1. Fastening an overlapping frame to a sandwich panel 1 - TDD 2 - door frame 3 - Erickson's nut 4 - Threaded rod М8 5 - Door hinge 6 - Self-tapping screw for fastening the frame components Figure 20. Assembly unit 2. Fastening an overlapping frame to a brick wall * 1 - TDD 2 - Door frame 3 - Anchor 10x92 4 - Self-tapping screw for fastening the frame components 5 - Door hinge * - wall thickness cannot be less than 160 mm 11. INSTALLATION OF DOUBLE-LEAF SWING...

12. INSTALLATION OF TDD WITH A CURVED U-SHAPED DOOR FRAME ● Before installing the doors, make sure that the leaves were not damaged during transportation. Check all parts are accounted for. ● Check the dimensions of the opening against the dimensions indicated in the door specification. Any deviation of the dimensions of the width and height of the opening cannot exceed ± 5 mm. Any diagonal deviation can also only be ± 5 mm. ● Assemble the frame components using M5x20 screws. ● Install the frame into the opening and check both levels: the posts vertically and the cross-beam horizontally. ●...

14. DOOR BLOCK ADJUSTMENT ● Stiffness adjustment or adjustment of the door opening force with COLDTECH swing hinges: 1. Remove the door leaf from the hinges by unscrewing the 4 screws securing the half-hinge. 2. Adjust the pressure with the adjusting screws. 3. Re-hang the door leaf and re-tighten the fastening screws. ● Stiffness adjustment or door opening force adjustment with KIDE pendulum hinges: 1. Remove the door leaf from the hinges by unscrewing 4 screws securing the half-hinge. 2. Adjust the pressure of the adjustment bolt. 3. Re-hang the door leaf and re-tighten the fastening screws