Polysol IPX-F

Product catalog summary

Product Overview
POLYSOL IPX F is an insulating system that combines a plastomeric waterproofing membrane with extruded polystyrene foam. The membrane is reinforced with glass fibre or non-woven polyester fabric, providing excellent thermal insulation.

Specifications
The system includes stiff, coloured polystyrene foam panels cut into 50 mm strips. The waterproofing membrane is made from a distilled bitumen-based compound modified with polypropylene, reinforced with polyester or fiberglass, and produced using NAT® technology to control ageing.

Applications
POLYSOL IPX F is suitable for waterproofing and insulating various roof types, including walkable and non-walkable civil and industrial roofs. It can be applied using different methods such as flaming with propane gas, glue, or mechanical fixings. A double-adhesive vapour barrier is also available.

Technical Characteristics

Thermal resistance (RD) ranges from 0.90 to 3.30 m2 k/W depending on thickness.
Heat conductivity (λD) ranges from 0.033 to 0.036 W/mk.
Compressive strength at 10% deformation is 250 kPa for 3-6 cm thickness and 300 kPa for ≥8 cm thickness.
Water vapour transmission is 80 m2h Pa/mg.
Long-term water absorption after immersion is less than 0.7%.
Reaction to fire is classified as Euroclass E.

Installation Instructions
1. Remove the insulating system from its package.
2. Position the roll over the vapour barrier and torch lightly for adhesion.
3. Fix and weld the overlaps.
4. Position the second roll and torch the side laps.
5. Cut the system for breather pipe insertion.
6. Complete additional necessary details.

Storage and Handling
Store POLYSOL IPX F in a dry place away from direct sunlight. Avoid contact with organic liquids and solvents, and prevent puncturing during installation.

Quality and Compliance
The product complies with European Standards and is certified under UNI EN ISO 9001:2008 and UNI EN ISO 14001:2004. Polyglass is a member of the Green Building Council.

Catalog excerpts

EXTRUDED POLYSTYRENE FOAM POLYSOL IPX F is an insulating system obtained through the hot bonding of a smooth or mineral-coated plastomeric waterproofing membrane reinforced with glass fibre or non-woven polyester fabric to strips of extruded polystyrene foam. Guaranteed Quality UNI EN ISO 9001:2008 and UNI EN ISO 14001:2004 Polyglass is a member of Green Building Council Product in compliance with European Standards Bituminous membrane polymeric matrix ageing control POLYSOL INSULATING SYSTEMS

Open the catalog to page 1

PRODUCT DESCRIPTION POLYSOL IPX F is an insulating system obtained through the hot bonding of a smooth or mineral-coated plastomeric waterproofing membrane reinforced with glass fibre or non-woven polyester fabric to strips of extruded polystyrene foam. This system offers excellent performance in terms of thermal insulating. THERMAL INSULATING DESCRIPTION Stiff, coloured polystyrene foam panels extruded and foamed from a molten and expanded thermoplastic mass are cut into 50 mm strips. BONDED MEMBRANE DESCRIPTION Plastomeric waterproofing membrane made of a distilled bitumen-based compound modified...

Open the catalog to page 2

UNIT OF MEASURE m2h Pa/mg COMPRESSIVE STRENGTH AT 10% DEFORMATION DIMENSIONAL STABILITY UNDER SPECIFIED TEMPERATURE AND HUMIDITY CONDITIONS For proper design, the values of λD should be increased as reported by the UNI EN ISO 10456. Materials and products for the building. Properties humidity. Tabulated values of project and procedures for the establishment of technical standards and declared the project. PLASTOMERIC MEMBRANE W/POLYESTER FABRIC (MINERAL) PLASTOMERIC MEMBRANE W/POLYESTER FABRIC PLASTOMERIC MEMBRANE W/GLASS FIBRE(MINERAL) TECHNICAL CHARACTERISTICS THICKNESS WEIGHT PER UNIT AREA...

Open the catalog to page 3

POLYSOL INSULATING SYSTEMS POLYGLASS SPA reserves the right to make any and all modifications required for the ongoing perfection of the product without notice. APPLICATION METHOD Q Remove the insulating system from its package. ^ Position the roll over the vapour barrier and torch it lightly for the adhesion of the system. © Fix the overlap and weld them. © Position the second roll. ©/© Lightly torch the side laps. © Cut the insulating system for the insertion of the breather pipe (beneath the vapour barrier). ® /© After the breather pipe has been inserted, make the other details necessary....

Open the catalog to page 4

Polysol IPX-F

Polysol IPX-F

Catalog excerpts

All Polyglass Spa catalogs and technical brochures