ecoTRONIC100 Heat Pump Controller
4Pages

{{requestButtons}}

Catalog excerpts

ecoTRONIC100 Heat Pump Controller - 1

Heat pumps ecoTRONIC 100 Ground source heat pump controller Operation mode The ecoTRONIC 100 is a weather sensitive controller designed to significantly increase the ground source heat pump efficiency. The controller displays large, editable graphics informations and parameters on a touchscreen with a dynamic scheme of existing hydraulic installation. In standard configuration this device can control two heating circuits*. The ecoTRONIC 100 is being equipped with stylish and modern touchscreen panel which gives the user full access to the controller as well to heat pump parameters and temperature or heat installation settings. An easy-to-use touchscreen and intuitive, smartphone-like user interface ensures comfortable way of operation. Additional equipment in form of an ecoNET internet module gives not only to the end user, but also to manufacturer or fitter a full remote access through Internet using PC, tablet or smartphones, for which there is a special mobile devices application. With the usage of ecoNET system fitters or heat pump manufactures can benefit from special remote access account for full control and supervision of given heat pump without physically sending maintenance team. After connecting our internet module to the controller, system will establish different type of accounts. Basic account is designed to give the user remote access to the controller but without possibility to edit service or manufacturer settings. The second stage of internet access is being provided for the fitters. With this kind of access fitters or maintenance team can supervise and also remotely edit service settings. Third and most sophisticated internet access is used by heat pump manufacturers and ensures unlimited remote control over the controller. The ecoTRONIC device measures the temperature and pressure of compressed as well expanded refrigerant and also the temperature of supply and return water temperature. There is also a function for preventing the evaporator from freezing and it is based on readings from temperature sensor, installed on the evaporator. Our controller supports also the function of regenerating the ground heat source – during summer there is a possibility to activate the pump without compressor operation in order to redirect the water into the ground. *up to 5 circuits with additional module PLUM Sp. z o. o. ul.Wspólna 19, Ignatki, 16-001 Kleosin, Poland plum@plum.pl www.plumelectronics.eu

Open the catalog to page 1
ecoTRONIC100 Heat Pump Controller - 2

Heat pumps Standard version scheme for ecoTRONIC 100 Technical data Temperature sensor inputs Pressure sensor inputs Digital inputs 6* pressure switches, flow measurement, energy meter, phase loss sensor, feedback from PWM pump, thermostat. Relay outputs or fan modulation Communication ports Additional heat source (heater, boiler) * Interchangeable temperature / pressure sensors Internet system Manufacturer Service

Open the catalog to page 2
ecoTRONIC100 Heat Pump Controller - 3

Heat pumps Advantages Compressor lifetime limit is being reached. The user will get this kind of information either as an alarm on the screen or by email (when the internet module was being connected). operation for reduction of compressor operation cycles. Thanks to this algorithm, the controller can adjust itself to the behavior of hydraulic installation thus extending the compressor’s lifetime. 3 operation modes with BURST mode Control over 1. Only heat pump operation. is so designed to maintain best possible pressure values for compressor and heat pump pressure installation in order to...

Open the catalog to page 3
ecoTRONIC100 Heat Pump Controller - 4

Heat pumps ecoTOUCH new era of touchscreen controllers ecoTOUCH series of products was made using advanced technology. These controllers are designed to use with heat pumps. The controller comes with intelligent menu solution, which makes disconnected components invisible on touchscreen. Patented Hint System allows the user easy and comfortable function operation. Additionally, there is a simple way to change the controller software with the help of microSD card. Unique design of TOUCH product series together with legible functions marked through icons is our answer for customer needs....

Open the catalog to page 4

All PLUM Sp. z o.o. catalogs and technical brochures

  1. SCP V

    2 Pages

  2. SVOC EX1

    1 Pages

  3. SRHT IN1

    1 Pages

  4. MacBAT 5

    4 Pages

  5. ecoVENT

    4 Pages

  6. ecoSTER 200

    2 Pages

  7. eSTER_x40

    2 Pages

  8. ecoMAX 800R

    2 Pages

  9. 850i v12

    4 Pages

  10. ecoMAX 200D

    2 Pages

  11. ecoMAX_800P

    2 Pages

  12. ecoNET 300

    4 Pages

  13. Solar systems

    16 Pages

  14. Fireplaces

    20 Pages

  15. Pellet

    6 Pages