GenieMat® FF
1 / 16Pages

It’s not magic, it’s engineering.® Impact and Airborne Sound Control GenieMat® FF Floating Floor Systems for Airborne & Impact Sound and Vibration Isolation

GenieMat® FF The next generation of acoustic floating floor PRODUCT FEATURES • Continuous underlayment system that limits surface area contact down to 4% at 1400 kg/m2 • Achieves low natural frequency with systems available as low as 6 Hz • Can be safely loaded over a wide range up to 100 kg/cm2 • Composed of 92% recycled rubber content • Helps to achieve HEA05 BREEAM credits • Mould, bacteria, fungi, and water resistant • Penetrations for pipes, ductwork, electrical conduits, and drains are easily accommodated • Rolls out quickly and is easy to install without the need for adhesive • Can...

EASY INSTALLATION ROLL IT OUT - TAPE THE SEAMS - READY TO POUR After installing perimeter isolation strips on the base of the walls, unroll GenieMat® FF. Duct tape all joints and seams, including between the perimeter isolation strips and the GenieMat FF. Pour screed, lightweight or normal weight concrete topping. Prepare concrete surface for floor finish. SIGNIFICANTLY IMPROVES INSTALLATION EFFICIENCY STEPS GENIEMAT® FF ROLL OUT SYSTEM PLYWOOD FORMWORK ISOLATOR BASED SYSTEMS SPRING JACK-UP TYPE SYSTEM Design isolator layout Coordinate load requirements with associated trades Install...

GenieMat® FF PHYSICAL PROPERTIES plan view Rollgood: 1.2 m wide, 9.1 m long Rollgood: 1.2 m wide, 9.1 m long Rollgood: 1.2 m wide, 4.6 m long Rollgood: 1.2 m wide, 4.6 m long Rollgood: 1.2 m wide, 4.6 m long Rollgood: 1.2 m wide, 4.6 m long COMPRESSIBLE ELASTOMER TECHNOLOGY ALLOWS FOR LOW NATURAL FREQUENCY AT LOW LOADS Typical vulcanized, natural, and neoprene rubber isolators are defined as incompressible. They require heavy mass loading in order to obtain adequate deflection, and consequently, vibration isolation. For applications where minimum loading criteria are not met, data shows the...

GenieMat® FF PROPERTIES 100 mm Concrete (2.4 kN/m2 Dead Load) product Typical Loading (19.2 kN/m2 dead + live load) critical natural damping ratio frequency (hz) critical damping ratio DESIGN PARAMETERS OF GenieMat FF SYSTEMS System Natural Frequency vs. Load Deflection vs. Load Load (psf) Pliteq GenieMat FF06 Pliteq GenieMat FF10 Pliteq GenieMat FF17 Pliteq GenieMat FF25 Pliteq GenieMat FF50 Pliteq GenieMat FF75 Pliteq GenieMat FF06 Pliteq GenieMat FF10 Pliteq GenieMat FF17 Pliteq GenieMat FF25 Pliteq GenieMat FF50 Pliteq GenieMat FF75 Deflection (Inch)

GenieMat® FF ACOUSTIC TEST DATA 150 mm STRUCTURAL SLAB WITH FLOATING CONCRETE TOPPING 100 mm Concrete Topping on GenieMat FF25 on 150 mm Structural Slab 4" Slab Slab 100Concrete mm Concrete GenieMat FF25 GenieMat FF25 6" Slab Slab 150Concrete mm Concrete 100 mm Concrete Topping on GenieMat FF50 on 150 mm Structural Slab 100Concrete mm Concrete 4" Slab Slab 150Concrete mm Concrete 6" Slab Slab 100 mm Concrete Topping on GenieMat FF75 on 150 mm Structural Slab 4" Slab Slab 100Concrete mm Concrete GenieMat FF75 GenieMat FF75

GenieMat® FF ACOUSTIC TEST DATA 60 mm Screed on GenieMat FF06 60 mm Screed GenieMat FF06 150 mm Concrete Slab 2 3/8" Gypsum Concrete FF06 GenieMat 6" Concrete Slab 60 mm Screed GenieMat FF25 150 mm Concrete Slab

GenieMat® FF ACOUSTIC TEST DATA 150 mm CONCRETE SLAB WITH PLYWOOD TOPPING 2 Layers of Plywood on GenieMat FF50 2x 12 mm Plywood GenieMat FF50 150 mm Concrete Slab 3 Layers of Plywood on GenieMat FF50 2 Layers of AdvanTech® on GenieMat FF25 50 mm AdvanTech Cement Board Raft on GenieMat FF25 17 mm AdvanTech Wood Subfloor 2x 17 mm AdvanTech Wood Subfloor GenieMat FF25 150 mm Concrete Slab 17 mm AdvanTech Wood Subfloor

GenieMat® FF ACOUSTIC TEST DATA CROSS LAMINATED TIMBER ASSEMBLIES 175 mm Cross Laminated Timber with 100 mm Concrete Topping on GenieMat FF25 GenieMat PMI12 100 mm Concrete Slab 175 mm Cross Laminated Timber 7" Cross Laminated Timber F5500.08 175 mm Cross Laminated Timber with 50 mm Screed Topping on GenieMat FF25 Vinyl Tile Vinyl Tile F6279.14 50 mm Screed 2" Concrete Slab GenieMat GenieMatFF25 FF25 175 mm Laminated Cross Laminated Timber 7" Cross Timber 175 mm Cross Laminated Timber with 100 mm Concrete Topping on GenieMat FF50 PMI 12 GenieMat PMI12 F5500.10 7" Cross Laminated Timber 175...

GenieMat® FF70 Modular Panelised Floating Floor Systems OVERVIEW Situations which involve: • Multiple sources of noise and vibration • Dynamic loads, and; • Large ranges of dead and live loads Require a system that is easily customised, easily installed on-site, but not to the detriment of airborne, impact, and vibration isolation. GenieMat FF70 modular panelised floating floor systems provide designers and installers this level of performance and adaptability. FEATURES AND BENEFITS • Low natural frequency at low loads • Customisable isolators • Comes in easy to handle panels nominal 610 x...

GenieMat® FF709R • Panels are made with 50 mm thick profiled isolation pads embedded in a layer of acoustic insulation • Natural frequency down to 10 Hz • Subfloor contact area reduced by 99% • ΔLn,w 35 GenieMat FF70LDM • Panels are made with 50 mm thick Low Dynamic Modulous proprietary Pliteq elastomer embedded in a layer of acoustic insulation • Natural frequency down to 6 Hz • Subfloor contact area with the floor is reduced by 96% • ΔLn,w 44

DESIGN PARAMETERS OF GENIEMAT FF70 SYSTEMS Airborne Sound Transmission Lightweight vs Heavyweight Topping Impact Sound Transmission Lightweight vs Heavyweight Topping Plywood - 19mm, GenieMat FF70 - 70mm, Concrete Slab - 150mm, Rw 61dB Plywood - 19mm, GenieMat FF70 - 70mm, Concrete Slab - 152mm, Ln.w 48dB Plywood - 19mm, GenieMat FF70LDM - 70mm, Concrete Slab - 152mm, Rw 63dB Plywood - 19mm, GenieMat FF70LDM - 70mm, Concrete Slab - 152mm, Ln.w 46dB Concrete Topping - 100mm, GenieMat FF70 70mm, Concrete Slab - 150mm, Rw 67dB Concrete Topping - 100mm, GenieMat FF70 - 70mm, Concrete Slab -...