SLABS
96Pages

built build tb SLABS

Support structures for slabs MP high load capacity towers 448 Accessories and spare parts 460

LITEFORM and the new reinforcement system for traditional slabs and slabs cast in place present the advantages of improving efficiency, reducing the assembly time and increasing safety on site.

Company | Projects | Products It is a security lightweight formwork for traditional and cast in site slabs, it has been designed with the purpose to increase safety on site, improve productivity and reduce slab implementation times. The system is especially suited for residential construction with rafter and hollow block slabs but it is also suitable for monolithic concrete slab. Safe (it is assembled from below), handy and easy to be assembled (aluminium panels are very light), modular and highly productive, LITEFORM is the reinforcement system for slabs ideal for small and...

The use of the LITEFORM system increases the safety and tidiness on site.

Company | Projects | Products rOPILOSIO • complete safety during the stage of assembly, disassembly: the frame assembly takes place from the bottom with no risk of falling from above* • the reduced spacing between the frame stringers allows positioning the brick or plywood slab for casting safely the monolithic slabs. The clearance between • the frames have a non-slip surface that allows working safely even with wet surface • the handiness and reduced weight of individual components in aluminium reduce the assembly and disassembly times • the modularity of the system and its easiness to be...

Weight of LITEFORM falling head 5.3 kg. It is suitable for monolithic slabs up to 26 cm thick (without lightening) and conventional brick slabs.The expected loads can change from 4.5 to 7.0 kN/m2 with values for single prop from 9 to 15 kN. It included the use of Class B or Class D props (according to EN 1065). It can be used with any type of Liteform shore head. A special latch prevents accidental release of the head from the shore. amount of props (1 every 2 m2) to significantly reduce the material to be handled with respect to traditional reinforcements. Weight of LITEFORM fixed head 2.0...

Company | Projects | Products rOPILOSIO

Before installation, the props must be reinforced with the related dismantling heads or fixed head It is sufficient to insert the head into the props the hooking device, prevents the accidental ejection and rotation of the head. Reinforce the props with the related dismantling or fixed heads and place a first row of props by using the tripods (Fig. 1). Position the frames on the heads (it is sufficient only one operator): the special hooking allows a safe installation, without risk of accidental slipping out of the head from the prop (Fig. 2) The positioning of the frames on the heads can...

Company | Projects | Products

The modularity and lightness of LITEFORM system is useful also for restoration operations.

Company | Projects | Products Scheme with beams R. Load on frame with section breakers R kN Load on prop with section breaker R** kN Maximum deformation with section breaker R mm Total load on frame kN Maximum load on prop kN * Workers overload: 2x0.15 kN. ** under operating conditions. Standard scheme.

TECHNICAL CHARACTERISTICS LITEFORM ALUMINIUM FRAME 491100200 491075200 491050200 LITEFORM ALUMINIUM INFILL FRAME 2 BARS AND 3 BARS 2000x1000 2000x750 2000x500 LITEFORM ALUMINIUM INFILL FRAME 7 BARS 4.4 3.8 6.8 5.8 B HOT GALVANIZED OUTER RING NUT PROPS ACCORDING TO EN1065 REGULATION LITEFORM QUICK DISMALTING HEAD 496000000 51B30FEZC load 12-27 kN (class B) ø int. 48.0 - ø est. 60.0 51B35FEZC load 12-27 kN (class B) ø int. 48.0 - ø est. 60.0 51D30FEZC load 20-35 kN (class C/D) ø int. 48.0 - ø est. 60.0 51D35FEZC load 20 kN (class C/D) ø int. 63.0 - ø est. 76.0 TRANSOM LITEFORM Accessories and...

TECHNICAL CHARACTERISTICS SLABFORM PVC INFILL PROFILE - LITEFORM WALL SUPPORTING ANCHOR COMPLETE K497000010 N° 1 S19 tie-rod of 750 N° 1 S19 wing nut LITEFORM FRAME-FRAME ALIGNING CONNECTOR 1000 750 500 VARIABLE GUARDRAIL POST - LITEFORM ASSEMBLY FORK - Company | Projects | Products

Slabs LITEFORM TECHNICAL CHARACTERISTICS PLYWOOD SHEET ALUMINIUM MOBILE TOWER Accessories and spare parts on page 460

Company | Projects | Products rOPILOSIO

Company | Projects | Products rOPILOSIO It is a modular system of formworks in aluminium for the execution of monolithic or lightened concrete slabs cast in place. SLABFORM is a fully industrialized formwork system that does not require specialized labor for assembly. The ideal use is in presence of monolithic or lightened slabs It is also used in casting of traditional joist and hollow block slabs and above all for the safety it ensures during work SLABFORM formworks belong to Class 7 according to the prEN 15113-1. The system consists of a limited number of components that includes...

Company | Projects | Products rOPILOSIO • ideal for casting concrete monolithic slabs. The system is also sized for very thick slabs placed at a high altitude • the components are handled manually: the panels are in aluminium and weigh less • modular lightweight and intuitive, it allows a very high productivity: 3 operators can assemble up to 500 m2 per day of SLABFORM formworks with slab intrados of 3 m • it allows a significant reduction in the time of casting rotation on site thanks to the dismantling head system • the special hooking of the dismantling head allows a safe installation,...

ALUMINIUM PANELS MAIN BEAMS IN ALUMINIUM PROP HEADS

Company | Projects | Products rOPILOSIO LOAD TABLE USING THE BEAM SLABFORM OF 224 CM AND PANELS OF 75X100 CM AND 75X75CM. formwork of 75x150 cm - beam spacing A=150 cm formwork of 75x75 cm - beam spacing A=75 cm panel beam prop deflection unit tension > allowable tension oanel beam prop deflection "props with 282 average extension

DISARMAMENT PHASE

Company | Projects | Products SLABFORM SITE